• Recent Articles

  • Hottest Threads

    Patrick Walsh

    Vintage Martin T75 restoration

    Thread Starter: Patrick Walsh

    So I have a opportunity to purchase the above machine for a fair deal from my employer. I am aware of the phenolic guides being pop riveted I the the sliding table along with not availible for replacement. So my question is as follows to those in the know with regard to the phenolic ways....

    Last Post By: Gustav Gabor Today, 7:26 AM Go to last post
    Matt Lau

    Shelves vs cabinets? Pegboard? Other?

    Thread Starter: Matt Lau

    Hey Creekers, I hope this isn't a stupid question. I will be trying to organize my workshop over I'd like your thoughts on workshop storage. What are your thoughts on shelves, vs cabinets? Pegboard? Other?

    Last Post By: Günter VögelBerg Yesterday, 1:57 PM Go to last post
    Brian Elfert

    19 year snow blower dead - I don't think anything new will last as long

    Thread Starter: Brian Elfert

    My 19 year old Troy-Bilt snow blower is dead. A bearing support for the auger broke and no longer available. This was one of the last units made before Gardenway went bankrupt. This is not an MTD. This thing is a tank. It broke a few years back and the hardware store I bought it from said to...

    Last Post By: Brian Elfert Yesterday, 1:21 PM Go to last post
    Derek Cohen

    Drill Press Table

    Thread Starter: Derek Cohen

    A couple of weeks ago I took advantage of a Black Friday sale and purchased a Nova Voyager drill press for a great discount. This replaced a Taiwanese model I had for 25 years. Yeah, I know this machine is OTT, but it is an amazing tool. For those who are not familiar with the Voyager, it is a...

    Last Post By: Derek Cohen Today, 8:05 AM Go to last post
    Bert Kemp

    Shaving

    Thread Starter: Bert Kemp

    Well I use to shave everyday and get my blades from an online shave club. Over the last year or so since I don't get out as much I find I don't shave everyday sometimes I let it got for 2 or 3 days. Then I find my dbl blade razors don't do the job they get clogged up pretty quick and hard to rinse...

    Last Post By: Dave Lehnert Yesterday, 9:24 PM Go to last post
    Robert Stanton

    Mounting UHMW Sheet To Fence

    Thread Starter: Robert Stanton

    1. I've purchased a 1/4" sheet of UHMW to attach to my 80/20 fence. How often should I drill mounting holes? I have 4 nuts and probably need more (they aren't cheep). 2. The UHMW sheet has tool marks on it. I expected it to be smooth and perhaps glossy. I'm not sure this photo will matter but...

    Last Post By: Michael A. Tyree Yesterday, 6:05 PM Go to last post
  • How I Make Spiral or Twisted Finials



    From the first time I saw pictures of Stuart Mortimers signature twist work, I knew I wanted to try one myself, but I feared it was too difficult and time consuming. Stuarts book, Techniques of Spiral Work- A Practical Guide to the Craft of Making Twists by Hand, and an article in the May 2006 issue of Woodturning were the sources of inspiration and also great learning tools. It was when Mark Hubl showed his first spiral piece that I finally decided I would give it a try.There are many ways this work can be done, but here is the way I make twisted finials. As with any woodturning project, if something doesn't feel right to you, don't do it!!


    Here's how I do it:

    I would suggest using a piece of wood with straight grain and no knots. I have used Sycamore, Walnut, Holly, Ebony, White Pear, and Hormigo Negro. For this tutorial I am using Holly so the pencil lines can be easily seen.




    I have turned this piece to the shape I want, which is usually an elongated pear shape. I’m gradually trying to make these skinnier as I make more. The area to be cut out for the spiral is finish turned, the beads and teardrop are just roughed at this point. It’s important to leave a little “meat” on the top portion at the tailstock end for now because of the stresses caused by sanding. You want to leave this between centers for the entire job, the disc on the end will eventually get turned away.



    The layout consists of four evenly spaced horizontal lines called start lines. The index feature on most lathes makes this easy. The three vertical lines are pitch lines. These are easily done with the lathe running. On this example, the spokes, or bines as they are called, will make a ½ twist, This means when looking at the completed finial a bine will start at the bottom and stop half way around from where it began. You could also layout four vertical pitch lines, which would produce a ¾ twist. The spacing of these lines can be adjusted to change the pitch of the bines.




    Here is where a decision needs to be made. Do you want a right or left hand twist? For this example I chose a right hand twist, but being a southpaw, a left hand is easier for me. Using a pencil I have started at the intersection of a pitch line and start line and draw diagonally to the next start/pitch line intersection. These are called the cut lines. At this time, for safety sake, you should unplug the lathe. It will be used for holding the piece in a still position only.




    Using brad point bits, I have drilled holes on the cut lines. It’s important that each hole be drilled toward the center of the piece. I used a 4mm bit for the four holes at the top of the finial. All the others are 5mm. The reason for the 4mm holes at the top is to insure I have left enough wood where the diameter is smaller. You can always remove wood where necessary, but I haven’t figured out how to add it! I used Bosch bits that have a nice sharp point. This helps to stick the bit where you want and not run the risk of having the bit “skate”.One other thing to include is the importance of spacing the holes well apart. I’ve had more than one occasion where I drilled a hole too close to another and the chip out was bad enough to scrap the piece.




    The next thing I do is to route a shallow trough connecting the holes. Here is a close-up of the bit I use in a Dremel tool. It looks like a Roto-Zip bit, I’m not sure, but it was included with the Dremel. A 1/8” drill bit could also be used. The reason for the trough is to help prevent the bit from jumping out and skating across the surface. I hold the Dremel on a low angle and gently route a channel from hole to hole.




    Here, the shallow channels are completed and I’m ready to open things up between the holes using the same Roto-zip type bit. This bit cuts aggressively, so a light touch is best.




    All opened and ready for refining the shape of what will become the bines. The inside will be cleaned up also.

    A tungsten carbide burr works good for cleaning up the bines. I also use a needle rasp and some coarse rifflers to reach the inside of each bine. A microplane is handy to round over the tops of the bines, it will lay between two bines and round both.




    The bines are starting to take shape and almost ready for sanding, but not yet. You want to be careful
    to keep the bines equal in size. The tools used can be seen (although blurry) sitting on the lathe bed.




    Sanding has begun starting with 80 grit cloth backed sanding strips. I tear the strips to about 1/4" or
    3/8" in width. Continue through the grits removing scratches from the previous grit.



    The sanding is finished. On this piece I sanded to 1200 grit, then I buffed each bine with 2,000 and
    4,000 grit Abralon.



    The next step is to refine the beads and teardrop. A vortex tool or small skew is needed to finish off the beads. As the point is formed on the teardrop the disc will eventually fall off.




    A little sanding on the beads and teardrop, and it's done! The base can now be shaped to suit, or a tenon
    can be turned beneath the bead if it's to be used on a different lid. That about does it. Hope you enjoyed,
    and if you have any questions, don't hesitate to ask.
    Comments 48 Comments
    1. Dick Wilson's Avatar
      Dick Wilson -
      Richard, Great little tutorial, I will have to give it a try. Thanks Dick Wilson
    1. Ken Fitzgerald's Avatar
      Ken Fitzgerald -
      Richard,

      Fantastic tutorial! Thanks for providing it.
    1. Jim Burr's Avatar
      Jim Burr -
      Wow Richard...Super effort and the always epic results!!
    1. Chris Ricker's Avatar
      Chris Ricker -
      WOW Richard, you do beautiful work, Thanks for the tutorial!
    1. Jeff Krug's Avatar
      Jeff Krug -
      What a great job!!!
      You make it look easy. Your results are beautiful.
    1. johnny means's Avatar
      johnny means -
      Great tutorial. Any idea how long this one would take you?
    1. Richard Madden's Avatar
      Richard Madden -
      Quote Originally Posted by johnny means View Post
      Great tutorial. Any idea how long this one would take you?
      I can tell you I'm not fast at these. I would guess 2-3 hours, although I've never timed it. The sanding is most time consuming and the most monotonous. I'll walk away after sanding for awhile and work on something else. The shameful thing is I have heard from people who have watched Stuart Mortimer complete one in 45 minutes!!
    1. Jim Adkins's Avatar
      Jim Adkins -
      Richard...Nice job on the Tutorial. Great detail....enough that even I might be capable of doing one of these!! Thanks.
    1. Dick Wilson's Avatar
      Dick Wilson -
      Richard, I am working on a piece and decided to put a spiral final on it. I used your method of drilling the holes. I sure save a lot of time with the Dremel
    1. Bill Wyko's Avatar
      Bill Wyko -
      Oh you can bet I'm gonna do that!!!! I stopped in my tracks when I saw this. Maybe I'll give it a whirl next week. I'll post it when I do. Thanks so much for the tutorial. I love it.
    1. Michael Short's Avatar
      Michael Short -
      Richard,

      Thank you for taking the time to put this together and share it with the group.
    1. Bill Wyko's Avatar
      Bill Wyko -
      Actually couldn't wait. I started tonight. Made good progress until the battery died. I'll be back on it tomorrow. So far so good thanks to your tutorial.
    1. Robert McGowen's Avatar
      Robert McGowen -
      Very clear and useful tutorial. Thanks for the effort in putting this together.
    1. Richard Madden's Avatar
      Richard Madden -
      Quote Originally Posted by Dick Wilson View Post
      Richard, I am working on a piece and decided to put a spiral final on it. I used your method of drilling the holes. I sure save a lot of time with the Dremel
      There was one picture I could not get uploaded for some reason...it was of the carbide burr I use and highly recommend. Made by Kutzall, BN-18-E. They also have others that might be suitable. As Stuart Mortimer would say, "now that you know how, it's a matter of practice". Good luck, and don't get discouraged.
    1. Rob Szrama's Avatar
      Rob Szrama -
      I'm impressed. You should try more things.
    1. John Hart's Avatar
      John Hart -
      That's a great tutorial, Rick. I can see so many applications for this technique that my mind is awhirl right now. Thanks so much
    1. Richard Madden's Avatar
      Richard Madden -
      Thanks for all the comments. It sounds like Dick and Bill are giving it a try, and I wish them luck. In the beginning I had a success ratio of about 50%, but with lots of practice, things went better. Practice and persistence are key.
      Rob, you say I should try more things??? I'm always trying more things, like for the past several weeks I have been following Jim Adkin's excellent tutorial and attempting basket illusions. If any of you are seeking a challenge...a really big challenge, then I encourage you to give one of those things a shot!! Really gives you more appreciation for what Jim A. does, and he does such an excellent job at that!
    1. Bill Wyko's Avatar
      Bill Wyko -
      Well, I was making good progress and just about ready to sand when I heard that awful sound we all know and hate, the snap. It wasn't due to my method of work but due to my tailstock applying too much pressure. So for you guys trying this, just use the tailstock to steady the end once you start digging out material. Other than that it was going very easy thanks to your excellent tutorial.
    1. Doug Palmer's Avatar
      Doug Palmer -
      Thanks Richard, very informative. When you drill the holes how deep to you go? All the way through or halfway or other?
    1. Richard Madden's Avatar
      Richard Madden -
      Quote Originally Posted by Doug Palmer View Post
      Thanks Richard, very informative. When you drill the holes how deep to you go? All the way through or halfway or other?
      Doug,
      Drill to the center of the piece so all holes meet. Good luck and be patient.
  • Recent Polls

  • Recent Forum Posts

    roger wiegand

    Diamond cutoff blade.

    I've been using a Makita branded blade for several years now, through several major projects with no apparent loss in cutting ability. It cost about 4x

    roger wiegand Today, 9:14 AM Go to last post
    Matt Day

    How can this be

    Think about the volume of shipping amazon does. They’ve got their own delivery service in some areas too.

    And think about how many containers

    Matt Day Today, 9:12 AM Go to last post
    Derek Cohen

    Shooting board

    Greg, if you plan to get either the Veritas or LN #51-type shooting planes, then the best design for these is a flat shooting board and not a ramped board.

    Derek Cohen Today, 9:11 AM Go to last post
    Pete Staehling

    Lathe Choice

    I think I am finally ready to make the plunge on a new lathe. I bought a cheap HF bench top to get my feet wet and figure out what I wanted to do with

    Pete Staehling Today, 9:08 AM Go to last post
    Cliff Jennings

    Diagnosing the power supply

    Hi guys, thanks for the responses. I didn't have my box checked to get emails, so just came back and saw your replies, sorry about that.

    Cliff Jennings Today, 9:08 AM Go to last post