Sawmill Creek Woodworking Community - Powered by vBulletin
  • Register
  • Help

  • What's New?
  • Forum
  • Articles
    • The Sawmill Creek Press
  • Blogs
  • Donate
  • Sponsors
  • Friends of the Creek
  • Advanced Search
  • Home
  • Home
  • Cabinetry


  1. If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
  • Sections

    • Sawmill Creek News
    • Workshops
    • Woodturning
    • Social Woodworking
    • Tools
      • Lathes and Accessories
      • Table Saws and Accessories
    • Jigs and Fixtures
    • Cabinetry
  • Recent Articles

  • Hottest Threads

    Mike Heidrick

    Pole Barn 40X64X16

    Thread Starter: Mike Heidrick

    Signed a contract yesterday with S&L Builders out of Indiana for a 40X64X16 Pole Barn with a 10X24 porch. Build date August 18, 2014. Plan to install Pex for raidant floor heat. Concrete slab 5" thick. Also doing 1.5" closed cell foam under the pad. Built on Laminated posts in ground. Will...

    Last Post By: Mike Wilkins Today, 2:46 PM Go to last post
    steven c newman

    A new build thread?

    Thread Starter: steven c newman

    Well, the current one is about completed.. But, I am having a few health issues going on. Not sure IF I'll be doing another large project anytime soon. More in the line of something I can just sit down at the bench...and cobble something small. Was in the Hospital over the weekend..AFIB...

    Last Post By: Mike Baker 2 Today, 5:24 PM Go to last post
    Nick Mazzino

    High end table saw blade - which one to buy?

    Thread Starter: Nick Mazzino

    Hi all, I have a 2003 Unisaw I just recently bought and am finalizing setting up my first wood shop. And a porter cable 10" non-sliding miter saw. I would like to upgrade the miter saw in the future. I have been going back and forth on which blade to buy for my Unisaw. I originally was...

    Last Post By: Terry Kelly Today, 7:36 PM Go to last post
    Mike Dowell

    Can't decide between the JET and Grizzly 12" jp combo units

    Thread Starter: Mike Dowell

    I know there are a number of threads about this topic but they are years old, and manufacturers change designs over time. Considering that, what may have been a "con" before, could possibly have been updated out of these machines in the last couple years. Well, I had originally ordered a...

    Last Post By: Mike Heidrick Today, 10:28 AM Go to last post
    Marshall Harrison

    What to look for in a Shop Vac?

    Thread Starter: Marshall Harrison

    I'll need to get some kind of dust collection going pretty fast as if all goes according to lan I'll be setting up my new table saw today or tomorrow and adding a jointer on Saturday. I figure hooking up one at a time to my tools is a good starting point and the shop vac will still be useful...

    Last Post By: Dave Sabo Today, 8:13 PM Go to last post
    Matt Lau

    Those proud of their workshops, please post pics!

    Thread Starter: Matt Lau

    I'll finally be non-nomadic, and I'd like to finally build up a workshop. Before I get started, I'd love to get ideas. I'd love to see how you do things, and how you do things differently with all the disciplines here: tuners, neanders, power tool users, festoolies, etc. For those of you who...

    Last Post By: Neal Pringle Today, 3:40 PM Go to last post
  • Cabinetry RSS Feed

    Improving a Fireplace Wall with Cabinetry 

    by
    Russell Hudson
    • View Profile
    • View Forum Posts
    • View Blog Entries
    • Visit Homepage
    • View Articles
    Published on 03-14-2011 12:45 PM     Number of Views: 42228 
    Article Preview

    Russell Hudson shows how woodworking can be used to dress up and renovate an otherwise uninteresting wall. ...
    Read More Read More 20 Comments

  • Recent Polls

    What type finish for hand plane (Votes: 14)

    1. paint (Votes: 8)

    2. jappaning (Votes: 5)

    3. powder coating (Votes: 1)

  • Recent Forum Posts

    Stewie Simpson

    Saw Sets

    The Eclipse #77 (L175MM) was manufactured in 2 pin sizes to suit a wide range of ppi saws.


    Stewie Simpson Today, 8:49 PM Go to last post
    Bradley Gray

    3 Phase Bandsaw Questions

    You should also consider a rotary phase converter, home made or commercial. If you happen to have an extra 5hp 3phase motor this can be very cheap to

    Bradley Gray Today, 8:49 PM Go to last post
    Ken Fitzgerald

    It's spring time in Idaho

    Ronald,

    I was born in Illinois, graduated from HS in Illinois. My wife is from Illinois. My two oldest children were born in Illinois. I

    Ken Fitzgerald Today, 8:47 PM Go to last post
    Chris Parks

    Under Floor Dust Collection

    Let me clarify what I mean before everyone starts jumping to conclusions because maybe I have jumped to a conclusion. The conventional method of using

    Chris Parks Today, 8:47 PM Go to last post
    Wayne Lomman

    Sherwood Precat Orange Peel

    Gloss lacquers are actually more difficult to work with. The flatting agents in lower gloss products have the side effect of making sanding easier. Gloss

    Wayne Lomman Today, 8:41 PM Go to last post
  • Contact Us
  • Sawmill Creek
  • Archive
  • Terms of Service
  • Top
All times are GMT -4. The time now is 8:55 PM.
Powered by vBulletin® Version 4.2.5
Copyright © 2018 vBulletin Solutions Inc. All rights reserved.