• Recent Articles

  • Recent Article Comments Widget

    Bob Bollard

    Using CA Glue in Woodturning

    The fumes are bothersome. Is it safe to use a dust extractor to suck the fumes away? Or would the... Go to last post

    Bob Bollard 03-14-2019 12:07 PM
  • Hottest Threads

    Patrick Walsh

    Vintage Martin T75 restoration

    Thread Starter: Patrick Walsh

    So I have a opportunity to purchase the above machine for a fair deal from my employer. I am aware of the phenolic guides being pop riveted I the the sliding table along with not availible for replacement. So my question is as follows to those in the know with regard to the phenolic ways....

    Last Post By: Patrick Walsh Yesterday, 10:30 PM Go to last post
    Kris Cook

    New Shop Construction

    Thread Starter: Kris Cook

    I currently have my shop in a two-car garage. While I don't necessarily use both bays of the garage solely for wood working; for me the footprint of one bay is not adequate space to efficiently work. We are down-sizing and have just purchased a 100-year old house north of where we live now. The...

    Last Post By: George Yetka Yesterday, 11:06 AM Go to last post
    Bruce Day

    Two foolish mistakes at table saw cost me, dearly - Graphic Photos!

    Thread Starter: Bruce Day

    Not very long ago I was at the table saw trimming the last of four legs of a table I was building. I had turned the saw off for a second to clean some debris off then got ready to do the last one, when I made the mistake of using a push stick instead of my gripper or push block. After I got about...

    Last Post By: Steve Demuth Yesterday, 2:49 PM Go to last post
    John Isgren

    Outfitting the shop

    Thread Starter: John Isgren

    As I mentioned in another post I am in the process of building out a hand tool shop. This is my plans and wishlist so far: Planes Block plane - LN #4 LN, #5 Vintage Bailey, #7 LN - Stanley Handyman converted to scrub Veritas Joinery set -Small Plow, Skew Rabbet, Router, Medium Shoulder...

    Last Post By: John Isgren Yesterday, 3:52 PM Go to last post
    Kev Williams

    Ebay fiber laser, I'll be the guinea pig--

    Thread Starter: Kev Williams

    Out of sheer necessity- and my fascination with buying the cheapest of something to see if I can make it work :D (Usually I have good luck, my big Triumph for example) One of my customers picked up a job making parts for an established company that moved into town from CA, they sell worldwide,...

    Last Post By: Trey Tull Yesterday, 8:21 AM Go to last post
    Alan Heffernan

    Which Slider Miter Saw to buy?

    Thread Starter: Alan Heffernan

    My son is starting a shop from scratch and looking for the best miter/slider saw to buy. Best = accurate, repeatable, reasonable cross cut capacity, dust collection, and reliable. (Edit: added dust collection) He has just bought a new house with a full basement and will be building out his...

    Last Post By: Thomas McCurnin Today, 12:56 AM Go to last post
  • Reversing Switch for Grizzly G0658 Midi Lathe

    I purchased my Grizzly G0658 back in 2009. At the time I was a novice wood turner and I did not give any thought to whether I needed reversing capability on a lathe. I have since added a JET 1642VS-2, which has reverse, to my lathe cell. Having found that reverse is a handy feature after using the Jet for a while I decide it would be nice to have it on the Grizzly.

    This is the step by step procedure that I used to add reversing capability to my Grizzly G0658 Midi Lathe.
    Here is a before and after revision of the electrical schematic showing the addition of the reversing switch and its location in the electrical circuit.
    Original___________Revise

    The motor is a DC motor so to reverse its rotation direction the only thing that needs to be done is reverse the two motor power leads. For those of you with AC motors this would have no effect on your motor direction, however, internal connections in some AC motors can be swapped to change motor direction, check with your electrician.


    Swapping DC motor power leads can be accomplished easily with a DPDT (Double Pole Double Throw) On-On toggle switch. The switch will have 6 lugs (either spade style or screws) with the center two being made(connected) to either of the other two sets depending on the toggle handle position.
    It is actually two SPDT switches in parallel activated by one handle. The motor leads will be connected to the center set of lugs and the DC power leads will be connected to one set of the other lugs. A set of crossover jumpers will be used to "reverse" the connections of the DC power leads to the other side of the switch. (See the following sketch)


    Now that we know where in the electrical circuit the switch is and how it works let's take a look at where it could be placed physically on the lathe.


    Front___________ Rear

    The best place would be on the front of the lathe along with all the other controls. However, there is no room in the G0658 control panel. There is room in the motor control box and that would be convenient for accessing the motor leads but being on the rear of the lathe it is not very handy for in process use.

    I opted for a location on the headstock just above the control panel.





    This will be a little harder installation but much more convenient then other alternatives. Notice that in this case removal and drilling of the head stock is involved.
    Now that we know where we want the switch let's get to installing it.
    Although this procedure applies specifically to a Grizzly G0658 wood lathe the general concepts and procedures could be used on any DC motor operated device but in all cases you should check with a certified electrician and electronics technician before attempting the modification.






    Step 1: FIND AND REMOVE THE MOTOR LEADS FROM THE MOTOR CONTROL BOX


    UNPLUG THE POWER CORD. THEN Remove the 4 small screws (P1) that hold the motor control box onto the lower belt access door. Open the door and disconnect the two ground wires from the door (P1). Verify which lead is the motor lead, it will be the one coming directly from the motor. Pull the two motor lead spade lugs from the control board (P2) being careful not to damage the board.

    P1________________P2
    Using a pair of pliers squeeze the plastic strain relief together (P2) and remove it and the motor lead from the motor control box. This may take some effort. Be careful not to crack the control box.




    Step 2: REMOVE THE SPEED SENSOR FROM THE HEADSTOCK



    P3_______________P4________________P5

    Open the top belt access door. Loosen the small Allen screw (P3) that retains the sensor. Slip the sensor down and out of the mounting bracket (P4). In P5 you will see a small nylon retaining loop that you will have to slip the sensor through.

    Step 3: REMOVE THE FRONT CONTROL PANEL FROM THE LATHE BASE



    P6________________P7

    Loosen the power cord strain relief (P6) and push the power cord through it 2-3 inches. Loosen the 3 small socket head set screws, two on the left, one on the right of the control panel (P7). Pull the control panel free of the base. Fish out the speed sensor and it's cord and lay the sensor aside out of the way, do not detach it's cord from the control panel.


    Step 4: REMOVE THE HEAD STOCK AND FISH IN THE MOTOR LEAD


    P8_______________P9________________P10


    Remove the four socket head cap screws that hold the headstock on (P8). Set the headstock aside. Fish the motor lead cord from Step 1 into the headstock opening (P9). The cord should be routed beneath the motor then up at the left end of the housing base. In P9 you see me checking the location of the motor leads. I have the lead temporarily attached to the switch and am holding the switch in its approximate final position. This allowed me to see where I might need to add cable clamps to restrain the lead out of the way of the belt pulleys. In the process I noted an unused hole in the end of the base housing (P10). It looked like a perfect place to attach a cable clamp or strain relief. I tapped it to M6-1 all the way through from the outside and was able to installed a plastic loop style strain relief for the motor lead. The loop will hold the cord next to the base wall well away from the pulleys.

    Step 5: DRILL AND COUNTERBORE THE HEADSTOCK AND ASSEMBLE SWITCH


    You may have noticed that I have already drill the switch hole in the headstock. That would have been all that was necessary if I had gotten a switch with a longer mounting. In my case it was fairly short and the wall of the headstock was too thick for the switch to accept it's retaining nut.


    P11_______________P1212________________P13a



    P13b________________P13c


    I clamped the headstock onto my drill press and used a 5/8" end mill to counter bore the previously drilled hole to give me room for the switch retaining nut.(P11-12) Again this would have been unnecessary if I had ordered a more appropriate switch.


    In either case, right switch or counter bore, install the switch into the head stock and tighten the retaining nut.(P13a) Since I was unable to get a wrench on the retaining nut I turned the switch instead and stopped when it was in a properly lined up side to side orientation. To make sure it did not loosen up I applied a small drop of CA to the nut so that it would wick into the threads and under the nut being very careful not to get any in the switch. Again something that would not be necessary with the right switch. There is a need for a ground connection close to the switch so while at the drill, drill a 5mm hole at the location shown in photo P13b-c. Tap it to M6-1.


    A word of caution: The sensor ring on the spindle shaft is magnetic so take care that you don't get metal shavings all over it.

    Step 6: INSTALL NEW SWITCH LINE FROM MOTOR CONTROL



    P14_______________P15________________P16________________P17


    For this step and remaining steps you will need six 14-16 gauge 1/4" female spade lugs, Two14-16 gauge ring lugs, and about 18" of 14-3 appliance cord. These are illustrated in P14. I used a piece of an old extension cord.



    On one end of the cord trim back about 6" of the external insulation. Trim the black and white wires to about 2" and remove about 1/4 inch of insulation from all three wires.



    Install two of the six spade lugs on the black and white wires. Install one of the ring lugs on the ground wire. Reinstall the strain relief removed in Step 1 onto the new cord about 4 inches from the end of the outside insulation. Crimp it tightly with a pair of pliers and hold it together while you insert the lugged end of the cord and it into the motor control box. It will go into the box in the same location as the original motor lead cord (P15).



    Slip the two spade lugs onto the terminals from which you removed the motor leads back in Step 1. Now attach the new ground wire plus the one original to the door and tighten.


    Reassemble the motor control box to the door with four small screws from Step 1.
    To dress things up a bit I nylon tied the new cord and the original motor cord together as in P17. They will both terminate at the new switch.

    Step 7: CONNECT SWITCH LINE AND MOTOR LEADS AND REASSEMBLE LATHE


    o

    P18_______________P19______________P20_____________P21

    Place the head stock onto the lathe base so that the inside is accessible.

    Assemble two ring terminals to the two ground wires or do as I did, I had a larger # 10-12 gauge and put both wires into one ring terminal. Attach the ground wire terminal(s) to the head stock using an M6-1 bolt and the threaded hole drilled in Step 5 (P18).

    Cut two 1.75" jumpers from left over pieces of the extension cord, one white, one black. Strip the wires and assemble female spade lugs on one end of each jumper. Strip the wires on the "switch" cord (the green cord in my case) and strip the other ends of the two jumper wires. Twist the stripped end of the white jumper with the striped end of the white switch cord and assemble one spade lug to the twisted pair. Repeat for the black wires.

    You will end up with something that looks like the black and white wires in P18. Slip the original motor lead female lugs onto the center lugs of the new switch.

    Slip the new cord twisted double female lugs onto one end of the switch. Slip the female lugs at the end of the jumpers onto the other end of the switch making sure to cross the two jumpers (P19).

    Refer to the sketch "DPDT SWITCH WIRED FOR REVERSING" if you are confused.

    Now reinstall the sensor being sure to thread it back through the nylon clamp (P19LR) Tilt the head stock back into its original position and reinstall the four cap screws and tighten (P20). Reinstall the front control panel using the reverse of Step 3 (P21).

    Step 8: FINAL WRAP UP



    P22________________P23


    Pull the power cord back out to its original length through its strain relief. Refer to Step 3. Re-tighten the strain relief collar/nut. Realign the belt onto its pulleys checking it in all three positions that it does not rub any of the cords or the wires on the switch. Close up all access doors.

    Keeping your hand on the power plug, plug the power cord back in and watch for smoke and listen for arcing sounds. If all seems well check the front to ensure that the little green LED power light is on. Keeping your hand on the power switch, switch on the power and watch for smoke and listen for arcing sounds. The lathe should start rotating. Verify direction and that the VS knob works as usual.

    On my Jet 1642 the lathe is in forward when the "Forward Reverse" switch is flipped to the right. I wanted the Grizzly to be the same for consistency. Of course when I tried it the first time it was the opposite. Not a problem, if that is your case as well unplug the lathe, release the belt tension, just open up the bottom access door, pull off the center motor leads from the switch and reverse them and slip them back on. If you have big hands there maybe some difficulty here but it is manageable. After the leads are swapped, repeat previous paragraph.

    You may want to add markings to the sides of the switch indicating direction once you have it going in the direction you prefer for the given switch position (P22). I just used a magic marker but may try to get some labels on it "someday".

    Assuming that all is well now grab you a turning blank and get busy.
    Hope this was helpful to someone and if so I would appreciate some feedback through Sawmill Creek.

    Thanks:
    JD Combs
    Comments 2 Comments
    1. Terry Murphy's Avatar
      Terry Murphy -
      Excellent write-up!

      Terry
    1. Don Nicholas's Avatar
      Don Nicholas -
      A most interesting and informative article, Thanks for posting.
      I have the exact lathe.
      Thanks again
      Don