• Recent Articles

  • Hottest Threads

    Patrick Walsh

    Vintage Martin T75 restoration

    Thread Starter: Patrick Walsh

    So I have a opportunity to purchase the above machine for a fair deal from my employer. I am aware of the phenolic guides being pop riveted I the the sliding table along with not availible for replacement. So my question is as follows to those in the know with regard to the phenolic ways....

    Last Post By: Patrick Walsh Today, 1:16 PM Go to last post
    Mike Heidrick

    Pole Barn 40X64X16

    Thread Starter: Mike Heidrick

    Signed a contract yesterday with S&L Builders out of Indiana for a 40X64X16 Pole Barn with a 10X24 porch. Build date August 18, 2014. Plan to install Pex for raidant floor heat. Concrete slab 5" thick. Also doing 1.5" closed cell foam under the pad. Built on Laminated posts in ground. Will...

    Last Post By: Mike Kees Yesterday, 9:09 PM Go to last post
    Patrick Walsh

    1982 Martin T-23

    Thread Starter: Patrick Walsh

    And so it seems it begins again. The T-75 isn’t even technically done and I have a new project. I’m not gonna go all buggy on this one “just yet” if ever. I will 100% go all the way through the machine and make sure it is 100% fully functional to the 9’s. 10’ for me if it was a term. If anything...

    Last Post By: Patrick Walsh Today, 1:12 PM Go to last post
    Ken Fitzgerald

    Shop lighting......

    Thread Starter: Ken Fitzgerald

    Here's an article that answers a lot of shop lighting questions that are so often asked here. http://www.sawmillcreek.org/content.php?146-Lighting-the-Small-Workshop-by-Jack-Lindsey

    Last Post By: Bill Webster Yesterday, 9:51 PM Go to last post
    Andrew Pitonyak

    Help me understand the MSDS for Honing Oil

    Thread Starter: Andrew Pitonyak

    Help me understand the MSDS for Honing Oil. Remember, I have not had Chemistry since high school, in the early 1980's. Norton Sharpening Oil - Highly refined Mineral Oil I was told that Norton Sharpening Oil is not much more than highly refined mineral oil and the MSDS was pretty easy to...

    Last Post By: Mel Fulks Yesterday, 10:13 PM Go to last post
    Thomas Wilson

    Complete set of Lie Nielsen bench planes

    Thread Starter: Thomas Wilson

    Some aficionados here haunt the antique auction sites. Some buy premium brands, either Lie-Nielsen or Veritas. Some buy functional knock-offs, like Wood River. Some buy seriously inexpensive hard to tune brands. I fell in with Lie-Nielsen 20 years ago and have been satisfied with the quality...

    Last Post By: Tony Zaffuto Yesterday, 3:30 PM Go to last post
  • How to Build the Magnetic Marble Roll

    Woodworking for Kids: Building a Magnetic Marble Roll. Jack discusses the design and assembly of an intriguing toy for kids.


    The Magnetic Marble Roll
    (actually uses mini porcupine type balls)



    Years ago my son’s daycare moved. At their new location there was absolutely no playground equipment. I’d seen kids have a pretty good time on those small climbing domes and thought one could be built fairly easily from electrical conduit. I went ahead and built one and brought it to the playground. The reaction from the moms and kids was amazing. They acted like I’d built the Eiffle tower. This started me down the path of building things for kids and eventually to setting kids up to build themselves. Here are directions for the marble roll and a bit about how the design evolved.

    A few years back I was teaching children’s carpentry and science and a friend lent me a small wooden marble roll to use in class. It consisted of two upright 1 X 4’s connected by sloping, grooved troughs. The marbles rolled down the troughs, reversing direction in a zigzag fashion, to the bottom. The kids loved it! They would roll one marble down by itself, then two or three, then a whole handful. Over and over and over again. They used it so much it began to bother me. What could they possibly be learning?

    Another friend mentioned that the Museum of Science and industry in Vancouver, B.C. hand a giant velcro ball roll. I went to take a look and discovered a large wall covered with velcro. Beside the wall was a box of small troughs made from plastic plumbing pipe split lengthwise. Each trough was fastened to a velcro backed L-bracket. The troughs could then be placed anywhere on the velcro wall. By moving the troughs around, an infinite number of paths could be made. Children could design and then build their own marble roll.

    I made a scaled down version with a 3’ X 5’ sheet of velcro. It worked fine at first but gradually the velcro sheet wore out and the troughs would fall off. What about using magnets instead of velcro? I replaced the big velcro sheet with a piece of sheet metal and the velcro on the back of the troughs with sheet magnet. This worked great and still works after ten years.

    Children learn from what the adults around them do. If adults make things then children learn interesting, useful and even sometimes beautiful things can be made by people, not just purchased. The Magnetic marble roll is such a project. Kids can help with construction sanding, drilling holes, and fastening the troughs to the backing boards. Best of all, from an adults point of view, once finished, the marble roll requires practically no supervision. You will not believe how much fun and learning take place. My admittedly biased opinion is that every school and children’s museum should have a magnetic marble roll.



    TOOLS

    • An electric drill, battery powered is fine. A hand drill will work.
    • Drill bit: for the 12-32 1/2” bolts and for countersinking the bolt heads. The bit which drills the holes and countersinks and the same time make things easier.
    • Screwdriver bit for drill
    • Screw driver to match the bolt heads.
    • A vice to hold wood while cutting is nice but not absolutely necessary.
    • Hand saw. A bands saw will make cutting the pipe faster.
    • Metal file for filing the bolt ends smooth,

    MATERIALS

    The Backing
    • A piece of galvanized sheet metal about 3’ X 4” and a 3’ X 4’ piece of 3/8” plywood for backing the sheet metal. Because I really liked the idea of recycling, I also tried an old refrigerator door. It turn out the doors usually have a thin plastic or vinyl coating which makes the thin magnets not stick quite so well. Use the medium thickness magnet sheet and you’ll be OK. Also, I could never find a paint hardy enough to hold up to the constant rubbing of the troughs so the door became all marked up from the constant rubbing of the magnets.
    • 1 X 2, about 14’, for trim to go around the edge of the plywood and cover up the galvanized metal edge which could be sharp.
    • 1/2” ring nails (I used bronze boat nails) to fasten the sheet metal to the plywood board.
    • short sheet rock screws (16 or so) to fasten through the back of the plywood, through the sheet metal and into the trim.
    • a 1 X 6 about 3 feet long (maybe a bit shorter), a 3” door hinge, and a 2’ piece of thin rope. These will be for a stand to keep the marble roll standing up.

    The balls, Pipe, and Troughs

    • First off, although I call this a marble roll, the name somehow stuck, but I never have kids use marbles. Marbles tend to roll all over and have to be chased down. Porcupine balls are the best because they roll slower and stay fairly close to the marble roll. Available from Oriental Trading company.
    • 7’ of 2” white plastic plumbing pipe
    • 2” plumbing pipe connectors: four 90˚, four 45˚, two tee’s, two sleeve connectors
    • 75 1/2” 12-32 flat head bolts with nuts to fasten the pipe and pipe fittings to the boards.
    • contact cement to glue the magnet sheet to the boards. The water base stuff works and isn’t so toxic.
    • 3 1/2 or 4 square feet of magnetic sheets (get medium strenght sheet) with adhesive backing cut into 1 1/2” strips
    • eleven feet of 1/4” thick by 1 1/2” wide soft wood such as pine or cedar, for the wood pieces to mount the pipe troughs and connectors. These need to be flat, in order to accept the magnetic sheet, light so they’re not too heavy for the magnets, and of uniform thickness so the troughs will line up when mounted on the door. I just slice some pieces off a good cedar 2 X 4. I used plywood once but it warped.
    • A small box approximately 2” X 3” to catch the balls. This could be wood, cardboard, plastic or something fancier like a band saw box. It needs to be light.
    • A box to hold all the pieces. I usually make a box about 5” wide by 3 1/2” high by 40” long. This box can sit right up next to the marble roll so if the marble roll is being rebuilt the troughs are more likely to be in the box and therefore less likely to get squished. A cardboard will work too, but they tend to get pushed out of the way.
    • 100 grit sandpaper

    CONSTRUCTION



    Fasten the sheet metal to the plywood. with the 1/2” nails. Its probably easier to drill through the metal first. Just nail around the edge and then put the trim over the top of the
    nails, fastening through the back of the plywood into the trim with the short sheet rock screws.

    PIPE





    • Cut the pipe down the center lengthwise and then it cut into lengths: four 10” lengths and eight each of 6” and 8”. Although it is hard to hold, the pipe can be cut with a fine tooth hand saw. A band saw will do the job quickly. Sand the edges of the pipe smooth.

    WOOD
    • Cut the 1/4” thick wood into 1 1/2” strips. Cut it into lengths to match the pipe lengths. 6” pieces for the 6” pipe, 8” lengths for the 8”, and 10’ pipe. Sand smooth.

    ASSEMBLY
    • Fasten the sanded split pipe to the wood pieces with the 1/2” bolts. I put the bolt head on the wood side. You must countersink it enough to keep the bolt head below the surface of the wood so the magnet sheet can be glued flat without a bump at the bolt. The nut goes on the pipe side. File the ends of the bolts flat if they stick through the wood. Two bolts to each pipe or fitting.
    • Fasten pipe connector pieces to wood backing pieces in the same manner as above. File bolt ends flat if they protrude.
    • Cut and fit magnet sheets for the wood on the back of each pipe piece (troughs and connectors). Apply contact cement to the back of each wood piece and after it dries remove the protective backing from the adhesive side of the magnetic sheet and fasten magnetic sheet to back of wood pieces.
    • Attach wood and magnetic sheet to the small box same as above.

    TEST
    Make sure all the troughs and pipe connectors fit flat on the sheet metal. Then find some kids!
    Comments 9 Comments
    1. John Coloccia's Avatar
      John Coloccia -
      This is GREAT. I was thinking of tossing some things like this together for my wife. She's a psychologist who works with kids, and she's always looking for these kinds of activities to help some of kids with concentration, and things like that. I love the PVC!
    1. Roger Thoreson's Avatar
      Roger Thoreson -
      Always looking for something to fun and useful to make for the grandchildren. This looks like a sure winner. Thanks Jack.
    1. Stan Powers's Avatar
      Stan Powers -
      My grandchildren are a little too young yet, but it will be a great project for them to help with in a couple of years. Thanks for sharing
    1. David Gaab's Avatar
      David Gaab -
      This is great! My family was just at the San Francisco Exploratorium and they had an area with a similar setup - except using pegboard. My nephews (8 &12) were there for 1.5 hours, and had a blast. Judging from the # of people around, it was a real hit. What was really fun was seeing kids working together and really putting their brains to work. I will try to find a photo. I really dig this version as it looks a bit easier for kids to adjust and tweak than the pegboard version (which was also darn cool).
    1. Michael Wildt's Avatar
      Michael Wildt -
      Nice toy!!

      Easy to make and it sure is a blast even for adults.

      Boston's Children museum has a whole wall with similar setup. Unfortunately no pictures of it on they website: http://www.bostonchildrensmuseum.org. It uses golf balls if I recall correct.
    1. Jack McKee's Avatar
      Jack McKee -
      Quote Originally Posted by John Coloccia View Post
      This is GREAT. I was thinking of tossing some things like this together for my wife. She's a psychologist who works with kids, and she's always looking for these kinds of activities to help some of kids with concentration, and things like that. I love the PVC!
      John,
      Part of the way I got interested in building stuff for kids was that my wife was and occupational theripist who worked with kids. She was always needing something designed for a specific kid/need. Here is a busy box I built. I actually built two versions of this and one is still in use after 25

      Attachment 179116years.
    1. Mike Gager's Avatar
      Mike Gager -
      forget kids, id build one of these for myself!
    1. Mike Heidrick's Avatar
      Mike Heidrick -
      I think this is a super awesome idea and build. Thank you.
    1. Guy Bratt's Avatar
      Guy Bratt -
      I'm a little late here but how's this... a colored paddle wheel mounted on bearings that the ball sets into motion. I can see wild Rube Goldberg setups with levers and triggers.
  • Recent Polls

    What's your opinion? (Votes: 20)

    1. It's a shame, that could have been some really nice wide panels. (Votes: 17)

    2. Yesssssss, the world can never have enough heavily checked cookie tables. (Votes: 3)

  • Recent Forum Posts

    Tom Bender

    Is a 12" jointer needed?

    Easy peasy, remove the steps, fill the hole with sand, place the planer on the sand, shovel the sand out underneath.

    Tom Bender Today, 1:52 PM Go to last post
    Lisa Starr

    It is always the easy stuff that bites you

    As already mentioned, our son purchased his 1st home and it was a foreclosure. We've completed the demo of the 3 basement bedrooms (I wouldn't have let

    Lisa Starr Today, 1:50 PM Go to last post
    Clark Hussey

    Deck cleaner

    For several years, I washed houses, decks and roofs. For a dirty deck it would usually come clean with about a 1% bleach solution. Just apply let it set

    Clark Hussey Today, 1:46 PM Go to last post
    Tom Bender

    Featherboards

    Glen you're the king of featherboards .

    Tom Bender Today, 1:44 PM Go to last post
    John Keeton

    Wedding ring

    Some years ago I was climbing down from a tree stand. I had installed metal screw-in steps in the tree, and as I was dismounting from the last step my

    John Keeton Today, 1:43 PM Go to last post