• Recent Articles

  • Hottest Threads

    Jefferey Scott

    Oklahoma Homestead 40x80x12

    Thread Starter: Jefferey Scott

    Hey guys, I'm in the early planning stages for a workshop that will be used as both a woodworking shop and a metal fabrication shop. I'm trying to figure out how much lighting I can afford to put in and have a rough floorplan with 21 - 4 foot 4 bulb high bay fluorescent fixtures (at about $60 a...

    Last Post By: Jefferey Scott Today, 7:21 AM Go to last post
    Julie Moriarty

    Martin OM Style Acoustic Guitar

    Thread Starter: Julie Moriarty

    Here we go... I'm using plans from LMI. The guitar is based on Martin's OM model. Two sitka spruce soundboard pairs were purchased from Alaska Specialty for $8@ I also bought some sitka splits for the braces

    Last Post By: Jim Becker Yesterday, 7:47 PM Go to last post
    Ken Fitzgerald

    Shop lighting......

    Thread Starter: Ken Fitzgerald

    Here's an article that answers a lot of shop lighting questions that are so often asked here. http://www.sawmillcreek.org/content.php?146-Lighting-the-Small-Workshop-by-Jack-Lindsey

    Last Post By: John Pegal Today, 8:22 AM Go to last post
    Mark Rainey

    Saddle square

    Thread Starter: Mark Rainey

    The Lee Valley saddle square looks nice. It looks like you can make one by gluing the edge of a flat piece of wood to the face of another piece of wood then crosscutting at 90 degrees. Anybody make one & is happy with it?

    Last Post By: Bob Glenn Today, 10:28 AM Go to last post
    lowell holmes

    Sketchup

    Thread Starter: lowell holmes

    I just ran across a Bob Lang video on my computer that I had forgotten about. It is a Pop Wood video about Sketchup. I am curious if any of you use the software. I have it, have used it, but don't anymore.

    Last Post By: Bob Lang Yesterday, 6:33 PM Go to last post
    Mike Dowell

    DC hose for Minimax FS41c?

    Thread Starter: Mike Dowell

    Oh my, this machine hasn't been here a week, and it's "loving me long time". I got all my DC fittings and was going to run a 6" drop to the machine, and pickup a 4" flex-hose to the ports. The problem? The ports aren't 4"!!! I'm sorry if I'm sort of "internet yelling". I am just at my ends...

    Last Post By: Jim Becker Yesterday, 9:09 PM Go to last post
  • Sawmill Creek News RSS Feed

    by Published on 02-27-2011 5:33 PM     Number of Views: 14883 

    Do you have woodworking knowledge you're just dying to share?
    Want to be an author at Sawmill Creek?

    Now you have a new area to publish articles!

    If you want to publish an article, you can join our authors group, which gives you access to a forum which is open only to would-be authors at SawmillCreek. This is a staging area for new articles, where you can post a new article, and we'll review for publication. Once you're ready to publish it, we'll promote it on the front page of SawmillCreek!


    The process is simple:

    1. Join the Authors group by visiting this page.
    2. Once you have access, visit the Authors forum.
    3. Start your article by creating a new thread in that forum.


    TIPS

    If your article is too long for a single post, don't fret ! Spread your article over multiple posts, and we'll merge them together into a single post when the article is ready to be published.

    Try posting pictures inline for visual interest.

    Choose a catchy, yet descriptive title!

    Writer's Block?

    We're looking for tool reviews, woodworking tips, woodturning techniques, jigs and fixtures, finished projects step-by-step, finishing techniques, social woodworking experiences, and even good compilations of our existing thread topics.

    Good luck and Happy writing!
    _Aaron Koehl_

  • Recent Forum Posts

    Louie Sherwin

    Bowl Gouge Grind

    Hi Brian,

    There are two possible problems that can happen if your wings are curved and you are using Stuart's style of push cut. Keep in

    Louie Sherwin Today, 11:39 AM Go to last post
    Reed Gray

    Bowl Gouge Grind

    The curved wing vs straight wing is one of the things we argue about.... I can't really tell that it makes any difference, but that may be because of

    Reed Gray Today, 11:35 AM Go to last post
    glenn bradley

    Miter Gauge Stops

    I used one of these. You can also make something similar out of a slotted strip of hardwood.

    glenn bradley Today, 11:33 AM Go to last post
    glenn bradley

    Jet Bandsaw Table Flatness- Not

    I'm with Charlie and Lowell. Dad's saw table looks great with a straight edge on it but his miter gauge and sleds always gave a little snag at the slot.

    glenn bradley Today, 11:31 AM Go to last post
    Kev Williams

    Generac pressure washer

    Guess I'm the only one here WITH a Generac? It's a 2700psi unit, it wasn't all that expensive, I've had it 4 years I think, maybe longer, it's used regularly,

    Kev Williams Today, 11:29 AM Go to last post