Jointer question

[Lee Schierer]

On another forum, I was reading a post where a person made a cutting board with end grain making up the cutting surface. You know, the butcherblock idea. Apparently some gaps go left in the glue up of the blocks and there was a suggestion to cut the glue line, run the pieces across a jointer and re-glue. Pkay so here's the question. Can you run grain sideways across a jointer such that the grain is running parallel to the cutters?

I've jointed some end grain when the knives are sharp and the cut is shallow, but never needed to do face grain sideways.

[Ted Shrader]

Lee -

I have done it. The problem is splintering. Since the blades are cutting in parallel with the grain, it tends to peel vice cut. Sharp blades, slow feed rate and light cuts leave a serviceable surface.

Ted

[Jason Tuinstra]

Lee, would wetting the wood help to make the cut easier? I'm just thinking about all the problems that are solved when planing figured wood via a good misting. Just a thought. Regardless, those knives would still have to be scary sharp.

[Chris Padilla]

I would suggest running the board across at an angle but you would need a wide jointer for that...like an FS 41 Elite MiniMax J/P...coming soon.... :p

[Steven Wilson]

On another forum, I was reading a post where a person made a cutting board with end grain making up the cutting surface. You know, the butcherblock idea. Apparently some gaps go left in the glue up of the blocks and there was a suggestion to cut the glue line, run the pieces across a jointer and re-glue. Pkay so here's the question. Can you run grain sideways across a jointer such that the grain is running parallel to the cutters?

You might be refering to a post I made. I used a jointer plane (Bailey #7) to make the face smooth. This is only needed if your making a large glueup. In my case I had strips of 6 blocks and strips of 7 blocks. These would be alternated to give a staggard glue line. The width of the butcher block was 13 blocks. You can glue up two or three rows at a time (sometimes more) but eventually you'll notice a slightly uneven surface (i.e. < 1/32" ). This needs to be dressed before attaching more strips. A hand plane is the appropriate tool for this. Running that stack over a powered jointer would be a two man operation as the stack was well over 100lbs, not something you want to hump up onto a powered jointer, especially a small 6" ones as it would likely tip over.

[James Carmichael]

I would suggest running the board across at an angle but you would need a wide jointer for that...like an FS 41 Elite MiniMax J/P...coming soon.... :p

Sorry Chris, your statute of gloat limitations has expired, especially for stealth gloats disguised as help.

[Chris Padilla]

:eek: LMAO!! Okay, okay...got whipped on that one...I deserved it.... :o When it's in the gara...er...shop, I'll make a comment but until then.......... :rolleyes:

[Michael Perata]

(Acting a surrogate gloater for Chris Padilla)

Did you get that MINIMAX 20" BAND SAW set up yet.

[Chris Padilla]

Pssst, Michael:

http://www.sawmillcreek.org/showthread.php?t=9371

:)

However, still waiting on wheels and I haven't been able to wire 'er up yet.

[Michael Perata]

...oh, very nice. :)

Chris, know what they call a bandsaw without power? (Add appropriate punch line here!) ;)

[Mark Stutz]

...oh, very nice. :)

Chris, know what they call a bandsaw without power? (Add appropriate punch line here!) ;)


Boat Anchor

[Gary Whitt]

"Chris, know what they call a bandsaw without power? (Add appropriate punch line here!) "

Uh......
An Amish bandsaw? :rolleyes:

[James Carmichael]

Pssst, Michael:

http://www.sawmillcreek.org/showthread.php?t=9371

:)

However, still waiting on wheels and I haven't been able to wire 'er up yet.

Is that a direct-drive motor, Chris? I'm a bandsaw newbie and still learning about these things as I fiddle with my new 14" Ridgid (did I mention I got it on closeout, :gloat:), but that thing makes it look like a toy.

That saw is obviously much too big for your pickup, Chris. Besides, in CA, you'll never have enough electricity to run it, even with governor Grey Out gone. Anyway, I'll be glad to bring my big, beefy Dodge 4x4 out to haul it away for you, I'll even go halves with you on my gas ;) .

[Tim Sproul]

Hand plane will perform better than a power jointer, IME.

Use a backer board either way you go.

[Chris Padilla]

Is that a direct-drive motor, Chris? I'm a bandsaw newbie and still learning about these things as I fiddle with my new 14" Ridgid (did I mention I got it on closeout, :gloat:), but that thing makes it look like a toy.

That saw is obviously much too big for your pickup, Chris. Besides, in CA, you'll never have enough electricity to run it, even with governor Grey Out gone. Anyway, I'll be glad to bring my big, beefy Dodge 4x4 out to haul it away for you, I'll even go halves with you on my gas ;) .
James, a belt from the motor drives the lower wheel. I think the problem isn't the saw size...it might be the pick-up size but this truck is worth its weight in gold! Funny, people are always asking me if I want to sell it. I guess I should start asking how much they'll offer. It would take quite a bit for me to get rid of it.

[Mark Rios]

Chris, I thought that your very stealthy gloat was extremely clever. So much so that you can use my quota of gloats to continue your masterful use of this forum to make us all feel envious of your garag....er..shop. Gloat away. :D :D :D :D

[James Carmichael]

James, a belt from the motor drives the lower wheel. I think the problem isn't the saw size...it might be the pick-up size but this truck is worth its weight in gold! Funny, people are always asking me if I want to sell it. I guess I should start asking how much they'll offer. It would take quite a bit for me to get rid of it.

Who said anything about buying? I'm just offering to take it of of your hands before you break down the suspension on your truck or the CA greenies start protesting in front of your garag..eh..shop for having that tree-eating, kilowatt-sucking monster. Least I could do for a fellow creeker :rolleyes:

[Chris Padilla]

James,

I promise you'll be the first one I call when I'm ready to give the BS away! :D