Rob Will
02-07-2008, 12:15 AM
Here are some photos of my dust collector installation (in progress).
The system is based on an Oneida 7.5 hp belt drive blower that I direct mounted in a vertical position above the Oneida 28" diameter cyclone. The entire assembly is mounted on a 3x3" steel tubing frame.
The cyclone inlet is 10" and the first section of spiral pipe is also 10". Hopefully this will provide for smooth air flow prior to entering the cyclone (and enhanced chip separation). Everything here is USA made. Oneida cyclone, NY blower, Lindab Union Made pipe and fittings.
So far, all I have done is mount the 10" pipe and 8" pipe to the wall and hook up the PM 225 planer with 8" pipe (I just had to try this thing out:D). There are a few details yet to work out on the planer hookup.
The cyclone and blower are mounted in an unheated garage area. This provides easy chip removal to the outside doors. From the 10 x 10" blower outet, 12" metal pipe returns the air back to the three 18 x 62" filters mounted in a storage room and back inside the conditioned space.:) (We are framing the partition wall later this week)
To control sound and to minimize sound transfer back into the shop, the 10" suction pipe is mounted to the cyclone with a neoprene coupler - no metal to metal contact. I also had perforated metal and 1" sound deadening material installed inside the filter plenum.
One thing that I am really proud of is the method of hanging the spiral pipe on the wall. It was cheap, fast, and easy. The hangers are cut from 3/4" birch plywood on the bandsaw. The size of the hangers and offset from the wall varies depending on the pipe size. (The pipe centerline stays the same regardless of size). The hangers are drilled with two pocket holes on each side and screwed to the wall. I used 2-1/2" screws and each hanger will hold 200 lbs. (I tested each one:o) Easy to fabricate and install. If any changes are needed, these brackets (being from wood) are easy to change or modify. Brackets are painted with latex house paint to match the wall before installation. Spacing on the wall is every 4'.
I hope you like this and maybe somebody can use this pipe hanger idea.
Rob
The system is based on an Oneida 7.5 hp belt drive blower that I direct mounted in a vertical position above the Oneida 28" diameter cyclone. The entire assembly is mounted on a 3x3" steel tubing frame.
The cyclone inlet is 10" and the first section of spiral pipe is also 10". Hopefully this will provide for smooth air flow prior to entering the cyclone (and enhanced chip separation). Everything here is USA made. Oneida cyclone, NY blower, Lindab Union Made pipe and fittings.
So far, all I have done is mount the 10" pipe and 8" pipe to the wall and hook up the PM 225 planer with 8" pipe (I just had to try this thing out:D). There are a few details yet to work out on the planer hookup.
The cyclone and blower are mounted in an unheated garage area. This provides easy chip removal to the outside doors. From the 10 x 10" blower outet, 12" metal pipe returns the air back to the three 18 x 62" filters mounted in a storage room and back inside the conditioned space.:) (We are framing the partition wall later this week)
To control sound and to minimize sound transfer back into the shop, the 10" suction pipe is mounted to the cyclone with a neoprene coupler - no metal to metal contact. I also had perforated metal and 1" sound deadening material installed inside the filter plenum.
One thing that I am really proud of is the method of hanging the spiral pipe on the wall. It was cheap, fast, and easy. The hangers are cut from 3/4" birch plywood on the bandsaw. The size of the hangers and offset from the wall varies depending on the pipe size. (The pipe centerline stays the same regardless of size). The hangers are drilled with two pocket holes on each side and screwed to the wall. I used 2-1/2" screws and each hanger will hold 200 lbs. (I tested each one:o) Easy to fabricate and install. If any changes are needed, these brackets (being from wood) are easy to change or modify. Brackets are painted with latex house paint to match the wall before installation. Spacing on the wall is every 4'.
I hope you like this and maybe somebody can use this pipe hanger idea.
Rob