Outfeed Table Plans & Ideas

[Bill Davis 0302]

I recently purchased a Delta X5 Unisaw and am in the process of trying to figure out an outfeed table design. I have quite a bit of room in my shop for my saw,but I would still like to be able to roll it around if I need to. Does any one have any plans, pictures, or tips that may help me? Thanks

[Matt Meiser]

I built this one which just clamps to my back rail. http://www.sawmillcreek.org/showthread.php?t=52774&highlight=outfeed

[Jim Becker]

There is a free plan on my web site for a folding outfeed table system that is just fine with regard to mobility. Many folks have built it or adaptations of it over the years.

[Rob Will]

I think Norm built a work table on NYW last week but I don't see it on the website.
It had wheels that drop down and lock.
Pull a rope and the wheels release.
It was a pretty slick design.
Can be used for outfeed or work table.

I have a rolling table that is 4'x6'
A friend of mine has a 5'x5' stationary table with two different table saws 90 degrees apart.

Rob

[Steven J Corpstein]

Here is a link to my web site. It may give you some ideas on how to remain mobile, but still build the outfeed strong. I'm in the process of finishing it and plan on adding another 36" wide section attached with door hinges.

http://www.datasystemsltd.com/saw

[Bruce Page]

Here’s my Rube Goldberg version. 5th one down

http://www.sawmillcreek.org/showthread.php?t=5526

I have CAD (.dxf or .dwg) drawings. PM if interested.

[Lloyd McKinlay]

doubles as a downdraft sanding table. It's a rough adaptation of the table shown here. (http://www.woodworkersworkshop.com/plansshare/air_filter_downdraft_sanding_table.htm)

Got the squirrel cage fan free from a local heating company and doubled up the air filters. Since it moves a lot of air it also helps as a whole shop air cleaner and is well positioned if I am creating a lot of sawdust.

[John Hedges]

Here is one I made recently for my PM2000. It is also a router table and an assembly table

http://img.photobucket.com/albums/v237/hedgehog55/RouterTable/IMG_1000.jpg?t=1195428567

[Jim Fox]

Here is a link to my web site. It may give you some ideas on how to remain mobile, but still build the outfeed strong. I'm in the process of finishing it and plan on adding another 36" wide section attached with door hinges.

http://www.datasystemsltd.com/saw


Hey Steve, how do you like the HTC mobile base? I've been looking at them for a while now.

[Gary Keedwell]

Here is one I made recently for my PM2000. It is also a router table and an assembly table

http://img.photobucket.com/albums/v237/hedgehog55/RouterTable/IMG_1000.jpg?t=1195428567
Hey John, I really like your set-up. Is it your design?
Gary

[Don Stanley]

Here's what I made for my PowerMatic 64A contractors saw. It is very large compared to others, but I'm really glad I didn't make it smaller! I tend to use the table for other things when It's not being used for outfeed! I had to add additional support legs on the right side of the tablesaw, to make it stable (bottom picture); they can be folded back when you want to move the saw.

Although the Aluminum miter tracks look nice, it was very hard to align them with the tablesaw miter slots. I wouldn't do it this way again! In summary, I don't know why I waited so long to build one! Absolutely a must have for the shop.

http://www.ncwoodworker.net/pp/data/1012/thumbs/1_P1010663.jpg (http://www.ncwoodworker.net/pp/showphoto.php?photo=14519)

http://www.ncwoodworker.net/pp/data/1012/thumbs/2_P1010696.jpg (http://www.ncwoodworker.net/pp/showphoto.php?photo=14521)

http://www.ncwoodworker.net/pp/data/1012/thumbs/20_P1010874.jpg (http://www.ncwoodworker.net/pp/showphoto.php?photo=15080)

Here's a link to my Photo Album. You will find additional details under the photo's. http://www.ncwoodworker.net/pp/showgallery.php?cat=1012

[John Hedges]

Hey John, I really like your set-up. Is it your design?
Gary

Gary. Thanks, yes it is my design, and it has worked very well for me so far. Here is the original post with a lot more info.

http://www.sawmillcreek.org/showthread.php?t=67725

[Steven J Corpstein]

I like it really well. I didn't want a base that I kicked every time I bellied up to the saw. I have to move my saw out from the wall every time I use it and the HTC has seemed to hold up to the task.

[Ralph Barhorst]

I made a roll-about flip-top cabinet for my planer that I also use for an outfeed table. It works great and is dual purpose.

See this thread. http://www.sawmillcreek.org/showthread.php?t=19921

[Henry Cavanaugh]

John Very nice design. I am about to put the finishing touch on a similar router table design . I need to make a door for the router cavity. I was thinking less of an opening then you show. What has been anyones experience on proper amount of air to allow in . Hooked to a 1.5 HP DC

[Paul Gatti]

There is a free plan on my web site for a folding outfeed table system that is just fine with regard to mobility. Many folks have built it or adaptations of it over the years.

+1 for Jim's design. I built his outfeed table and attached it to my 1956 Unisaw. It works great. It is the best design I've seen if you want something that is attached to the saw and allows for easy mobility.

[Jeff Norri]

I sold the designs for a jacking out feed table to Wood Magazine. It is in issue 178. Here is the video of it - I have been happy with the design thus far and I have used it one form or another for a few years.

http://link.brightcove.com/services/link/bcpid979295690/bclid979255135/bctid1078950624

[Chris Padilla]

I sold the designs for a jacking out feed table to Wood Magazine. It is in issue 178. Here is the video of it - I have been happy with the design thus far and I have used it one form or another for a few years.

http://link.brightcove.com/services/link/bcpid979295690/bclid979255135/bctid1078950624 (http://link.brightcove.com/services/link/bcpid979295690/bclid979255135/bctid1078950624)

Great videos in that link, Jeff! Thanks for sharing.

[Bruce Page]

Clever idea Jeff.

[Jeff Norri]

Thanks - I like any idea that buys me new tools!

[Jeff Cremers]

Thats a great outfeed table. I found that issue and am going to make that my first real project (other than some 2 x 4 work benches).

But I do have a question Do I have to use Maple or can I use oak ( from home depot) or maybe even pine. I don't know if Maple is cheaper where you are and thats why you use it, well that and its a hard wood.
I really like your design and can't wait to try to start it in the next few weeks.
Jeff

[jim gossage]

i made this outfeed table from plans i found in a woodsmith issue earlier this year. the table is held up by a pair of heavy duty 16" locking/releasing shelf brackets. you just press a lever to drop the table down, and then lift it back up to open it. the frame is made of 2" thick ash and the table from two 1/2" sheets of baltic birch. i modified the frame to make it sturdier, added walnut trim, and enlarged the table size (30 x 52"). its not fancy but its built like a tank and can function as an auxillary work bench. my previous table had fold down legs and was kind of a pain in the butt to operate, and the legs got in the way of sweeping and moving the saw. i like this design much better.

[Marc Prudhomme]

Love that table.I realy love the mobil wheel set-up.Wish I would of saw that idea before I put wheels on my workbench
I sold the designs for a jacking out feed table to Wood Magazine. It is in issue 178. Here is the video of it - I have been happy with the design thus far and I have used it one form or another for a few years.

http://link.brightcove.com/services/link/bcpid979295690/bclid979255135/bctid1078950624

[Fred Voorhees]

There is a free plan on my web site for a folding outfeed table system that is just fine with regard to mobility. Many folks have built it or adaptations of it over the years.

Count me in on one of those who have adapted Jims plans to use on my contractors saw. It has been a major addition to my shop. I am just about to part with it soon because a new saw is in the offing shortly so I will have to "adapt" again soon.:p

[Bob Feeser]

Matt,
I visited your link/thread and really like the idea of being able to use the Beis fence and measuring tape to set the fence. You have the advantage of using the tape for graduated passes, for example when making multiple passes on a raised panel. I see ingenuity at work.


I built this one which just clamps to my back rail. http://www.sawmillcreek.org/showthread.php?t=52774&highlight=outfeed

[Brian Penning]

The Wood Whisperer makes Norm's outfeed table. Episode 30.
http://thewoodwhisperer.com/
I made Jim becker's table and turned out well.

[Matt Meiser]

Matt,
I visited your link/thread and really like the idea of being able to use the Beis fence and measuring tape to set the fence. You have the advantage of using the tape for graduated passes, for example when making multiple passes on a raised panel. I see ingenuity at work.

You could, but I don't. I was just making a bunch of raised panels last night. I got everything set up exactly for the final pass, then loosened the clamps and put spacers between the fences and made a pass on all the panels. Then I took out that spacer and put in a very thin spacer and made another pass. Finally I made a pass with no spacers.