Rehabilitating Old Chisels (Big File)

[Bob Smalser]

I was in the market for a large framing chisel on Ebay and wound up with a package deal for 30 bucks…an old Stanley 5 Type 16…the Lakeside 2” Framing Chisel I wanted…a beater chisel with a mangled tang…and an old cooper’s shaping chisel:

http://pic3.picturetrail.com/VOL12/1104763/3302194/40494865.jpg

This article will deal with the two framing chisels…the cooper’s chisel was usable as is with some cleaning and sharpening, and the plane I’ll cover in another article, although I’ll rehabilitate them together. These will be put back to work as users, like all my tools…restoration of collector items is another subject. For this article, I’ll purposely use only the minimum tools and techniques necessary for a first-class job. My intent is to provide a model for newcomers to the craft who will benefit greatly from acquiring older but high-quality tools in need of a hug for very little money…and putting them back into service.

I use a large, 8” gunsmith’s pedestal buffer-grinder for most of my grinding and polishing chores, but a smaller 6” bench grinder will also work fine.

http://pic3.picturetrail.com/VOL12/1104763/3302197/40506072.jpg

I use a soft steel wire wheel to clean all metal parts thoroughly…the cooper’s tool has been cleaned in the shot above.

http://pic3.picturetrail.com/VOL12/1104763/3302194/40505579.jpg

Then I treat them with a phosphoric acid solution (above) available at home improvement chains to kill any remaining rust. This is the functional equivalent of using an electrolysis solution for those not so inclined. The phosphoric acid is allowed to sit over night to work. The next day, the black oxide rust residue is removed with the wire wheel in preparation for buffing and finish later…we need to do some rough grinding and make and mount the handles, first.

http://pic3.picturetrail.com/VOL12/1104763/3302197/40506067.jpg

The treasure of the lot is the one in the worst shape; of course…a Robert Duke Diamond Brand firmer-style chisel of lovely, glass-like cast steel. It had lost its handle ages ago and probably served to cut the head off nails with a large, ball peen hammer in its old age. The socket tang was badly mangled with the remnants of the old handle remaining in the void. The tang was returned to its original form by drilling and filing the socket mortise, and grinding off the metal extruded on the outside. Fortunately, there was enough socket mortise remaining to use or I would have required the services of a neighbor I trade work with and his TIG welder to build it up. Using heat-sink paste and wet rags, I might have been able to build up the socket with my torch welding setup without ruining the blade’s temper, but it would have been riskier, and I’m not near the welder my professional neighbor is.

http://pic3.picturetrail.com/VOL12/1104763/3302197/40505193.jpg

http://pic3.picturetrail.com/VOL12/1104763/3302197/41748405.jpg


As the blade was badly chipped and had lost its bevel, grinding was required. While I have a jig for this, I rarely use it any more and freehand the 25-degree bevel using lots of water…turn that blade edge 600-degree blue and it has lost its temper and all the blue must be ground away…and square and protractor to check my progress. You should use a 6” bench grinder with all the guards and a proper jig for this….and wear glasses, of course.

http://pic3.picturetrail.com/VOL12/1104763/3302197/40506079.jpg


As the other blades are in better shape, and I don’t prefer to leave the bevels of heavy chisels and slicks with a hollow grind (although not important…merely personal preference), I finish the grinding stage for my 25-degree bevels on the belt sander chucked in the Workmate. I use 60, 80, 100 and 150 grits lubed with WD-40 and lots of water, checking my bevel angle and edge with protractor and square as I go.

http://pic3.picturetrail.com/VOL12/1104763/3302194/40548925.jpg


Final honing of 25-degree bevel and 30-degree secondary bevel will come later.

Continued on Part II

[Bob Smalser]

http://pic3.picturetrail.com/VOL12/1104763/3302194/40495338.jpg

Next I rough out my handle stock. There are better choices for handles that occasionally will be struck, but I have some Honduras Mahogany left over from a boat project and will use that. I rip a 2” turning square of it on the table saw, 8-side it on the same saw, and cut two handles to length…the finished length of each handle to equal the length of blade and tang. I then 16-side them using a couple rehabbed old smoothing planes set for coarse and fine cuts.

http://pic3.picturetrail.com/VOL12/1104763/3302197/40973867.jpg

Then I move to the shaving horse and shape them into cylinders using two spokeshaves set for coarse and fine cuts just like the planes.

http://pic3.picturetrail.com/VOL12/1104763/3302197/40506249.jpg

Next I’ll fit the ferrules on the striking ends of the handles. These are simple sections of 1 ¼” brass pipe salvaged from an old plumbing fixture with hacksaw and buffer-grinder. The centers are laid out, an interior line penciled…

http://pic3.picturetrail.com/VOL12/1104763/3302197/40503836.jpg


…and the actual ferrule and masking tape used to lay out the cut line for the saw. The dovetail saw is marked with a piece of masking tape functioning as a depth gage, the ferrule shoulder circumference cut to depth, the waste pared away with gouge and chisel, and final fitting for a tight, drive fit done with the patternmaker’s rasp. I don’t want the ferrule to slide on easily without crushing wood, so I fit it so the ferrule has to be heated a bit to fit…coat the wood tenon with a bit of thickened and dyed epoxy, and drive on the hot ferrule.

I’ll also epoxy the chisel sockets later. Why glue them on? Well, thickened epoxy provides a microscopically perfect fit and rock-hard surface, so when the handle is struck thousands of times during its life there will be minimum wood crushing and the resulting camming action that will eventually wear it out. And when it has to be replaced eventually, it is a simple matter to heat the metal to the 110 degrees required to break the epoxy bond. This isn’t traditional construction, but it is unlikely that I or even my sons will have to replace these handles again in our lifetimes.

http://pic3.picturetrail.com/VOL12/1104763/3302197/40506244.jpg

I do similar to fit the chisel sockets. But as these are tapered, I find it convenient to use the sanding disk on the buffer-grinder, driving on the socket occasionally to mark high spots on the wood. You can see the high spots that have to be reduced where the fibers have been crushed shiny by the drive fit…but you can also use sooty smoke from an alcohol lamp burning mineral spirits, Prussian Blue machinist layout paste, or Mama’s lipstick to perform the same function.

http://pic3.picturetrail.com/VOL12/1104763/3302197/40496271.jpg


Next I want to lay out the shape of these 2” diameter handles. As my favorite handle shape is one I used for turning cherry handles for Grandpa’s old drawknife a couple decades ago, I simple eyeball the proportions for the new handles and lay out my guidelines using masking tape that I will simply slice through during shaping.

http://pic3.picturetrail.com/VOL12/1104763/3302197/40495817.jpg


The sockets are also driven on with thickened epoxy.

http://pic3.picturetrail.com/VOL12/1104763/3302197/41734999.jpg

After the epoxy cures, I rough out the shape using coarse spokeshave…

Continued on Part III

[Bob Smalser]

http://pic3.picturetrail.com/VOL12/1104763/3302197/41735047.jpg


…and coarse rasp. Note the selection of finer rasps and various old machinist files on the bench. The better you become at cross and draw filing and the better your selection of file grades, the less sanding you will have to do. And smile knowingly but ignore pundits who claim only cutting blades should ever touch fine wood. Like those folks who claim planes should always be left on their sides instead of their soles when laid down, these practices are hardly universal among master craftsmen…or even important, for that matter. I’ve seen it done both ways in dozens of shops I’ve worked in and observed…and I’ve seen it done both ways well. In fact, all the master stock makers I know always reach for the rasps when working thousand-dollar blanks of figured walnut for wealthy and discriminating clients…no risk of tear out in swirled grain that is impossible to read, let alone slice cleanly.

If you are confident using successive grades of abrasive paper, you should be just as confident in rasps. The work looks ugly, but the ugliness only extends to the depth of the teeth, and is removed with successively finer rasps with finer teeth…just like sandpaper. Rasps are really precision instruments. And those large old 3-dollar machinist files in flea markets do yeoman service on hardwood long after they are too worn to cut steel. Learn to use them, and you will never need or even be inclined to use a power sander on a sculpted surface like these…finish sanding becomes a snap.

Also note all the different file handles on the bench…some are nicely shaped…some are as ugly as toads. Like you rehabbing your own tools, they were all lathe practice from 30 years ago. And it’s good to have your reject work around in the shop to look at every day…the stuff that makes your teeth itch every time you look at it…helps keep your ego where it belongs.

http://pic3.picturetrail.com/VOL12/1104763/3302197/41735008.jpg


I finish sand the shaped handle in minutes with successive grits of 80-220. The 600 grit shown is merely used to polish occasionally as I go to reveal sanding scratches I missed. I also dampen the wood with water between each grit…it reveals scratches I missed, but more importantly, it swells the fibers in those scratches so they can be removed with little hollowing of the surface. It will also prevent the grain from raising beneath your finish when the tool gets wet for the first time. Another stock maker’s trick.

http://pic3.picturetrail.com/VOL12/1104763/3302197/41734982.jpg


With one handle completed for a model, the second and any subsequent handles can be made much faster, as there is a lot less trial and error eyeballing of your shaping progress involved. The first handle took 45 minutes to shape and sand, the second one will take 25 minutes. Don’t try to go fast, take your time, learn as you go and enjoy yourself…I’m just pointing out that with practice, this level of work can be done by hand at a decent pace.

As the Lakeside chisel in the vise is a paring-style rather than a firmer chisel, I won’t ever use it for striking and can make the shape of its handle a little finer. This will also serve as a tactile aid as I reach for them during work without looking.

http://pic3.picturetrail.com/VOL12/1104763/3302197/41735021.jpg

One nice-to-have tool for this work is a file with a “safe” or untoothed edge to mold those epoxied shoulders nicely.

To Be Continued….

[Mark Singer]

Bob,
Shows a lot of care and skill!
Mark

[Charles McKinley]

Thank You Bob,

I really enjoy reading your articles. Your talent is not only in your work but your ability to explain it so that I can understand the process.

[Marc Hills]

Bob,

Great article! There seems to be a moral impertive to take what was once a file tool, abused for decades, and then bring it back from the brink. It somehow restores a karmic balance to a universe populated by new Stanley planes, "toolbox" handsaws and cheap chisels indistinguishable from screw drivers.

Reading it makes me want to go out and acquire a few old chisel to refurbish. Except I'm not quite there yet in the tooling department. Please can we have Bob's post put in the articles section?!

Cheers

[Bob Smalser]

http://pic3.picturetrail.com/VOL12/1104763/3302194/41937550.jpg

The finishing materials I’ll use on the handles are Brownell’s “English Red” diatomaceous earth oil-based stock stain and filler and Birchwood Casey Truoil, a linseed-based soft exterior varnish.

http://pic3.picturetrail.com/VOL12/1104763/3302197/41813701.jpg

After buffing the new handles with a paint store tack rag and readying a holder for them, I thoroughly mix the stain-filler…

http://pic3.picturetrail.com/VOL12/1104763/3302197/41813613.jpg

…and apply the material thickly and allow a few hours for it to set up to a hard paste…but not rock-hard…consistency. Then I buff across the grain with a coarse rag, removing the surface paste but also rubbing it deep into the mahogany’s open pores. I then set the work back in the holder to dry overnight.

http://pic3.picturetrail.com/VOL12/1104763/3302197/41937385.jpg

The next day I buff with a soft rag and coat with Truoil varnish mixed with a couple drops of art store Cobalt Drier is applied. The heavy metal drier is useful because the new finish has to amalgamate chemically with the stain-filler…makes drying time a whole lot quicker. Truoil is a proprietary linseed product and more a soft exterior varnish than an oil finish…I like it for a finish on hard-used wood because it is renewable. It’s soft and wears off, but there’s never a need to destroy that lovely age patina with strippers…merely buffing with fine steel wool and more coats renews the finish.

Were this mahogany a high-end job to be finished with Tung or Behlen’s Bartop Varnish, I would add an additional step after grain filling I omitted here…gentle machine polishing on a loose muslin wheel with Tripoli followed by White Rouge polishing compounds…adds a depth to the work that approaches priceless age patina. As these handles will get a lot of handling and hard use in short order, I don’t really need to create artificial patina for them.

To Be Continued….

[Marv Arnold]

boy, I can't wait to find some old chisels to refurbish. Thanks for the great article.

Marv

[Bob Smalser]

I put on 4 coats of Truoil in a day, heating the handles with the heat gun to hasten drying. Each coat is rubbed with 0000 wool all the way back to the wood surface to insure the grain is fully filled and the finish surface is perfectly smooth.

http://pic3.picturetrail.com/VOL12/1104763/3302197/42016074.jpg

While the last coat of finish is curing, I buff the steel with Knifemaker’s Green and the brass with Tripoli polish. The steel is degreased with TCE and three coats of Brownell’s Oxpho Blue are applied…this steel stains stubbornly and I buff between coats with degreased steel wool…and buff the final coat with a coarse brown paper towel.

http://pic3.picturetrail.com/VOL12/1104763/3302194/40548193.jpg

My last task with metal is to finish hone the blades. It doesn't matter whether you use sandpaper/glass, waterstones, Arkansas stones or carborundum stones.... all can be made to work well and easily.... I see more need to practice rather than to spend big bucks on "systems".

I use the set of 4 Arkansas stones because I have them...but were I starting from scratch, I’d merely have my glass shop make up a half dozen thick glass plates and I'd use plain old alum oxide wet-or-dry paper mounted with spray adhesive (cleaned with razor-blade scraper) and lubed with WD-40. That's what I do for plane bottoms to overcome the stone's lack of width.

You can buy a honing guide or simply memorize your angles using your kid’s plastic protractor to set them. Clamping your sharpening media to a bench set at belt height or just below will facilitate maintaining your bevels without putting some rocker in them when freehanding…although a little rocker in your bevels is no big deal and you will undo it in future sharpenings as you gain practice.

I begin by flattening the lower inch of the blade’s back rather thoroughly through all four of my stones…then I hone the 25-degree main bevel using my coarse stones, followed by tipping the iron up to 30 degrees (softwoods) or 35 degrees (hardwoods) to put in a small secondary bevel using all four stones. Does it matter whether you use 30 or 35 degrees? Not much…shallower angles dull quicker on tough wood. But as your stones should live clamped to a corner of the bench when working, you will touch these blades up daily, anyway. Do that, and you will always have sharp tools and will soon toss your jigs in a drawer permanently.

http://pic3.picturetrail.com/VOL12/1104763/3302197/42016039.jpg

The result should shave hair painlessly.

http://pic3.picturetrail.com/VOL12/1104763/3302197/42016023.jpg

The final step is to rub out the cured finish. For a high-end piece and a semi-gloss finish, I would allow it to cure for 30 days while in use before rubbing out with pumice and rottenstone slurries on hard felt pads. But on these user tools, I will rub out immediately using 0000 steel wool lubed in Kiwi Clear Shoe Polish, a high-quality hard carnauba wax…and buff when dry.

http://pic3.picturetrail.com/VOL12/1104763/3302197/42016002.jpg

The final result looks good along side their big brother, the slick. Can you tell these handles were made with eyeball and rasp rather than a wood lathe? If you know what to look for, and hold them up silhouetted against a backlight…you can…but it will take you a couple minutes…and for fun, I’ll be glad to artificially age them and give even money over whether the Roadshow Twins can.



“When we build, let us think that we build forever. Let it not be for present delight nor for present use alone. Let it be such work as our descendants will thank us for; and let us think...that a time is to come when those (heirlooms) will be held sacred because our hands have touched them, and that men will say, as they look upon the labor and wrought substance of them, ‘See! This our father did for us.’ “ --John Ruskin.

Audels Carpenters and Builders Guide
1923 Theo Audel & CO. New York.

[Wendell Wilkerson]

So Bob after all these rehab projects, do you have any hair left on your arms :p Thanks for the great how-to articles.

Wendell

[Randy Klein]

Bob,

I'm trying out this technique and an old chisel and want to know how you clean out all the gunk and (maybe dried epoxy?) that's in the socket?

[Dewey Torres]

Very nice thread!
Dewey

[Jim Koepke]

I'm trying out this technique and an old chisel and want to know how you clean out all the gunk and (maybe dried epoxy?) that's in the socket?

Use what you have at hand.

A small torch would help to soften or burn things out, just rap the lower part of the chisel in damp rags. Do this outside as there may be a strong smell from what ever is in there.

An old stump of handle could be drilled then put a large screw into the wood. As the screw hits the bottom of the socket, the wood should be driven out.

No torch? Lacquer thinner will soften some epoxies. Do this outside and away from flame.

A tool could be made by driving a large nail into a handle, beat the end of the nail flat then shape with a file to scrape out the gunk inside.

Lots of ways to do the same thing.

jim

[Don C Peterson]

Great post as usual Bob. Thanks for sharing your knowledge and talents with the rest of us.

[Bob Smalser]

Very nice thread!
Dewey

Here's some more that may help:


Courtesy of Bob Smalser

Boatbuilding Tool Articles

Advanced Saw Filing and Reconditioning
http://www.sawmillcreek.org/showthread.php?t=66090&highlight=life

Straightening Bent Handsaws
http://www.sawmillcreek.org/showthread.php?t=63325

Block Plane Selection and Rehabilitation
http://www.sawmillcreek.org/showthread.php?t=60970&highlight=block+plane+selection+rehab

Basic Sharpening
http://www.sawmillcreek.org/showthread.php?t=12747

Spoke Shave Tune Up
http://www.sawmillcreek.org/showthread.php?t=7415

Rustproofing Tools
http://www.sawmillcreek.org/showthread.php?t=28340

Fettled a 5 1/4 Today
http://www.sawmillcreek.org/showthread.php?t=20347

Retro Lathe Tools
http://www.sawmillcreek.org/showthread.php?t=14189

Wood Chisel Survey for Beginners
http://www.sawmillcreek.org/showthread.php?t=13090

The Incredibly Versatile Sweep Brace
http://www.sawmillcreek.org/showthread.php?t=13090

A Better Coping Saw - Complete Tutorial
http://www.sawmillcreek.org/showthread.php?t=12368

Making Leather-Washered Chisel Handles
http://www.sawmillcreek.org/showthread.php?t=11538

Making Spar Planes
http://www.sawmillcreek.org/showthread.php?t=11233

Making a 50-degree Smoother
http://www.sawmillcreek.org/showthread.php?t=8136
http://www.sawmillcreek.org/showthread.php?t=8491

Rehabbing Woodies
http://www.sawmillcreek.org/showthread.php?t=8351

Tuning Card Scrapers
http://www.sawmillcreek.org/showthread.php?t=8352

Sharpening Handsaws
http://www.sawmillcreek.org/showthread.php?t=8198

Filing and Finishing Metal
http://www.sawmillcreek.org/showthread.php?t=7784

The Drawknife
http://www.sawmillcreek.org/showthread.php?t=7528

Rehabbing Old Chisels
http://www.sawmillcreek.org/showthread.php?t=5771

Rehabilitating Old Planes
http://www.sawmillcreek.org/showthread.php?t=5867

Shopmade Joiner Tools
http://www.sawmillcreek.org/showthread.php?t=5279
http://www.sawmillcreek.org/showthread.php?t=5280
http://www.sawmillcreek.org/showthread.php?t=5281



Boatbuilding and Woodworking Articles

The Haunched and Drawbored Mortise and Tenon Part I
http://www.sawmillcreek.org/showthread.php?t=13246

The Haunched and Drawbored Mortise and Tenon Part II
http://www.sawmillcreek.org/showthread.php?t=13260

Coopered Pocket
http://www.sawmillcreek.org/showthread.php?t=20605

Removing Three Inches of Twist
http://www.sawmillcreek.org/showthread.php?t=26813

Are Your Glue Joints Repairable?
http://www.sawmillcreek.org/showthread.php?t=21822

A Few Small Details (Chamberlain 19’ Gunning Dory)
http://www.sawmillcreek.org/showthread.php?t=21612

Bedding Hardware
http://www.sawmillcreek.org/showthread.php?t=21412

Fabricating in Bronze
http://www.sawmillcreek.org/showthread.php?t=21337

Traditional Centerboard and Case – Part I - The Board
http://www.sawmillcreek.org/showthread.php?t=16747

Traditional Centerboard and Case – Part II - The Case
http://www.sawmillcreek.org/showthread.php?t=17510

Traditional Centerboard and Case – Part III - Installation
http://www.sawmillcreek.org/showthread.php?t=19914

Pipe Rudder
http://www.sawmillcreek.org/showthread.php?t=16999

Traditional Interior Joiner References
http://www.sawmillcreek.org/showthread.php?t=14041

Machine Cut Through Dovetails
http://www.sawmillcreek.org/showthread.php?t=13905

A Simple 3-Board Door
http://www.sawmillcreek.org/showthread.php?t=10383

A Simple Pair of 7-foot Oars
http://www.sawmillcreek.org/showthread.php?t=10036

8-Siding Gage
http://www.sawmillcreek.org/showthread.php?t=9984

Repairing and Restoring Varnished Hardwood
http://www.sawmillcreek.org/showthread.php?t=7691



Articles on Lumber Production and Characteristics

Ring Count
http://www.sawmillcreek.org/showthread.php?t=9175

Air Drying Stacks
http://www.sawmillcreek.org/showthread.php?t=9102

Falling a Big Fir
http://www.sawmillcreek.org/showthread.php?t=5307

Milling Beveled Siding
http://www.sawmillcreek.org/showthread.php?t=8837

Pitch Pockets, Bullets and Slabs
http://www.sawmillcreek.org/showthread.php?t=8709

Big Madrone
http://www.sawmillcreek.org/showthread.php?t=8669

Milling Earl’s Fir

http://www.sawmillcreek.org/showthread.php?t=5277
http://www.sawmillcreek.org/showthread.php?t=5278
http://www.sawmillcreek.org/showthread.php?t=5294