View Full Version : chisel handles (pics)
George Conklin
02-15-2007, 2:20 PM
Here are three chisel handles that were made from cherry and finised with tung oil.
58006 58007
The two black gouges in 5/16 and 3/8. The handles measure approximately 12 and 14 inches long. The 1/2" flat nosed scraper is again, approximately 14 inches long.
Even though these are smaller tools, I made the handles longer for my comfort. I'm not a big fan of short handled tools.
I think the bottom of the flat nosed scraper handle looks the best.
Thanks for looking:) .
Paul Engle
02-15-2007, 2:30 PM
Nice work George, I like em longer also, i lengthined my factory handles and much more comfortable and confident.
Mike Vickery
02-15-2007, 2:35 PM
Very nice work George, mine never look like they match. I also like my handles a little longer than most.
John Hart
02-15-2007, 3:27 PM
Aw Man! Those are great George! My homemade handles are like limbs....leaves torn off...roughly sanded....sorta round. Nice work!!
Bernie Weishapl
02-15-2007, 4:15 PM
Hey George those are some dandy looking handles. Sure wish you would quit making that Hart fellow feel bad.:eek: :eek: :D :p
Andy Hoyt
02-15-2007, 4:45 PM
Nice handles ya got there, Otis. I like mine long (and heavy) too.
Steve Clardy
02-15-2007, 4:46 PM
Looks great George :)
George Conklin
02-15-2007, 7:05 PM
Nice handles ya got there, Otis. I like mine long (and heavy) too.
"Otis" LOL!:D
It's really good to have you back!
Larry McCumber
02-15-2007, 9:41 PM
Very nice handles, George. What did you do for the ferrules?
Thanks,
Larry
George Conklin
02-15-2007, 10:18 PM
Hi Larry,
Found the ferrules on ebay.
Mark Pruitt
02-15-2007, 10:28 PM
Nice handles George! I like them all but the middle one is my favorite.
Larry, you can buy ferrules from a number of places; Highland and Lee Valley are two good sources.
Chris Barton
02-16-2007, 8:09 AM
Hi George,
Nice looking handles there. I got one of the non-handled gouge sets from PSI for xmas and am in the process of doing the same thing. Nice post!
Ken Fitzgerald
02-16-2007, 9:18 AM
Nice handles George! Well done!
Tom Sherman
02-16-2007, 8:43 PM
Great handles George, I like you prefer the longer one with the scraper.
Gary Herrmann
02-16-2007, 9:00 PM
Very nice handles, George. Very clean looking. I've got to try that some day.
Jim Underwood
02-17-2007, 1:32 PM
Good looking handles. Reminds me that I need to go out and make some more tools...
Darrell Feltmate
02-17-2007, 1:56 PM
Nice handles George. They are fancier than what I make for myself but I lack patience. Besides, one of the reasons I make my own handles is my dislike of varnish on a handle. My favorite handle finish is oil from my hands :-) On the other hand, I do not think they would sell well finished that way. I also like them long and strong, especially for face plate work and for chisels. You know a friend gave me a couple of industrial planer blades about 2" across, 18" long and 3/8" thick. What a set of chisels those would make for newels and such. Hmmm, maybe some more handles... thanks George.
Darrell
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.