Michael Cody
09-06-2003, 9:55 PM
I know there are some poplar users here on the board.. I worked with my son on his new Futon (wood magazine plan) he's building for his first WoodShop project. Being 15 1/2 he needed to learn on something he can afford. He wanted to build it cheap as he could (since he's paying for half the wood -- well 1/4 anyway! since he didn't want to start w/something smaller) ... Link to picture below:
Sleeping Beauty Futon (http://us.st8.yimg.com/store6.yimg.com/I/woodstore_1748_5438523)
Plans called for maple but I suggested he go with something cheaper. He still wanted maple but then he saw the price .. plus is calls for about 50bf of 1.5" material and 'bout 40bf of 4/4 stuff. I talked him into laminating 4/4 so we could build out of 4/4 soft maple. Then he got counting the cost @ 2.68$-bf which is a pretty good price but adds up. Plus he was looking at a sheet of 3/4" Maple Ply (70$) too in addition to 1/2" birch ply(60$)...
We looked around, considered Australian Cypress (1.95bf)(too soft), Red Oak(no savings over maple), Alder (to many knots but great price @ 1.92 bf any qty) .. Found some #1 Maple a bit cheaper but a lot of knots to cut around ..
To make a long story short he decided on poplar, we sorted out S&B got 121bf -- he's going to laminate to get thicker stuff .. plenty extra to cover mistakes @ 1.57bf.
We went with all birch for the plywood... I am thinking here about how to finish it now..
Thinking on working on a mellow golden/amber tone ... to even out the variance. We picked almost all white wood with no green streaks, just some brown streaks here & there. One piece that has strong brown coloring which we plan to use for the top & bottom of futon platform. I looking for tips here.. I don't want to go just clear, but the grain is pretty nice and painting is out. This will not be a show piece but that doesn't mean he can't give it his best effort. My son does want me to leave him alone building it (which I will - mostly :D ) but he wants help on the finish.. It's just poplar and birch but we ought to be able to make it look even in tone.
How do you guys finish poplar ...?? Any help would be appreciated.
Sleeping Beauty Futon (http://us.st8.yimg.com/store6.yimg.com/I/woodstore_1748_5438523)
Plans called for maple but I suggested he go with something cheaper. He still wanted maple but then he saw the price .. plus is calls for about 50bf of 1.5" material and 'bout 40bf of 4/4 stuff. I talked him into laminating 4/4 so we could build out of 4/4 soft maple. Then he got counting the cost @ 2.68$-bf which is a pretty good price but adds up. Plus he was looking at a sheet of 3/4" Maple Ply (70$) too in addition to 1/2" birch ply(60$)...
We looked around, considered Australian Cypress (1.95bf)(too soft), Red Oak(no savings over maple), Alder (to many knots but great price @ 1.92 bf any qty) .. Found some #1 Maple a bit cheaper but a lot of knots to cut around ..
To make a long story short he decided on poplar, we sorted out S&B got 121bf -- he's going to laminate to get thicker stuff .. plenty extra to cover mistakes @ 1.57bf.
We went with all birch for the plywood... I am thinking here about how to finish it now..
Thinking on working on a mellow golden/amber tone ... to even out the variance. We picked almost all white wood with no green streaks, just some brown streaks here & there. One piece that has strong brown coloring which we plan to use for the top & bottom of futon platform. I looking for tips here.. I don't want to go just clear, but the grain is pretty nice and painting is out. This will not be a show piece but that doesn't mean he can't give it his best effort. My son does want me to leave him alone building it (which I will - mostly :D ) but he wants help on the finish.. It's just poplar and birch but we ought to be able to make it look even in tone.
How do you guys finish poplar ...?? Any help would be appreciated.