Russell Shelly
10-04-2022, 9:20 AM
I’m selling some planes to fund another purchase.
I have two Bedrock planes for sale, two Stanley Baileys, and an ECEmmerich block plane. I also have a Jackson dovetail saw with a curly maple handle and a Rob Cosman IBC 2” iron and chip breaker set.
The Bedrock 605 has recently had the sole touched up on a Starrett surface plate. It is in good shape, but is missing some Japanning. It comes with a Stanley iron/CB. $150
if you want to purchase the Rob Cosman one with it, I’ll knock some money off both. $225 for plane and RC Iron set
The Bedrock 606 has a corrugated bottom and is also missing some Japanning. It’ll come with a Stanley iron/CB. I haven’t used this one much but everything is in good working shape. $150 ($200 for the plane with a Hock iron and chip breaker paired set)
One Stanley Bailey no. 6C - comes with a Hock iron/CB set that has only been to the water stones a couple times. This one has been my go to shooting board plane, as well as nearing final prep, just prior to my smoother. It’s Japanning is pretty much 100%. It’s got the name of previous owner very nicely engraved in cursive on one side. That side also has some staining from Evaporust dripping on it from another project, and not immediately noticing, it stained. I keep it below my split top bench for quick access and the plastic lining I was using apparently sprung a leak allowing it to drip onto this plane. Total bummer because it was in flawless shape before that. $140
I also have an older Stanley Bailey no. 6 smooth bottom for sale with a Hock iron/CB set. This one is a pretty old plane (I forget the year but I’m almost positive it’s pre WWII). The Hock iron and CB are both new and have only seen the honing stones once. $175
Stanley Bailey no. 5, vintage, with Stanley iron - $80
Jackson Warranted dovetail/backsaw with curly maple handle. The handle is an exact replica of the original (which I’d throw in for you if you want it). The saw couple use a sharpening. I was going to grind the teeth into crosscut configuration, but I haven’t gotten around to it, so they’re in their original rip with very minimal set. $65
Rob Cosman/IBC Iron/Cap Iron set. Cosman developed these sets with IBC to help us all turn vintage planes into users that can compete with the newly produced versions of the classics. This set has his ingenious tab that extends through the iron to the lateral adjustment tab, making it possible to use this setup on any vintage Stanley Bailey or Bedrock plane. It took me a long time to get my hands on this one. It was out of stock for so long and is so once again. It’s only seen the honing stones once. $120 for the set
ECEmmerich block plane. Made in West Germany. I prefer metal planes. $65
I’ll attach some photos until I get frustrated with the program. Please PM me for more photos of each. I can email or text them to you much quicker than upload them here.
the photos look like they came out in this order from left to right
Stanley #5, Bedrock 605, Stanley smooth #6, Stanley #6 corrugated, Jackson saw, Bedrock 606C, Rob Cosman IBC Iron/CB, and ECEmmerich block plane.
located in Haddon Heights NJ. Will ship at buyers expense via PayPal or Venmo.
Thanks, Russ.
I have two Bedrock planes for sale, two Stanley Baileys, and an ECEmmerich block plane. I also have a Jackson dovetail saw with a curly maple handle and a Rob Cosman IBC 2” iron and chip breaker set.
The Bedrock 605 has recently had the sole touched up on a Starrett surface plate. It is in good shape, but is missing some Japanning. It comes with a Stanley iron/CB. $150
if you want to purchase the Rob Cosman one with it, I’ll knock some money off both. $225 for plane and RC Iron set
The Bedrock 606 has a corrugated bottom and is also missing some Japanning. It’ll come with a Stanley iron/CB. I haven’t used this one much but everything is in good working shape. $150 ($200 for the plane with a Hock iron and chip breaker paired set)
One Stanley Bailey no. 6C - comes with a Hock iron/CB set that has only been to the water stones a couple times. This one has been my go to shooting board plane, as well as nearing final prep, just prior to my smoother. It’s Japanning is pretty much 100%. It’s got the name of previous owner very nicely engraved in cursive on one side. That side also has some staining from Evaporust dripping on it from another project, and not immediately noticing, it stained. I keep it below my split top bench for quick access and the plastic lining I was using apparently sprung a leak allowing it to drip onto this plane. Total bummer because it was in flawless shape before that. $140
I also have an older Stanley Bailey no. 6 smooth bottom for sale with a Hock iron/CB set. This one is a pretty old plane (I forget the year but I’m almost positive it’s pre WWII). The Hock iron and CB are both new and have only seen the honing stones once. $175
Stanley Bailey no. 5, vintage, with Stanley iron - $80
Jackson Warranted dovetail/backsaw with curly maple handle. The handle is an exact replica of the original (which I’d throw in for you if you want it). The saw couple use a sharpening. I was going to grind the teeth into crosscut configuration, but I haven’t gotten around to it, so they’re in their original rip with very minimal set. $65
Rob Cosman/IBC Iron/Cap Iron set. Cosman developed these sets with IBC to help us all turn vintage planes into users that can compete with the newly produced versions of the classics. This set has his ingenious tab that extends through the iron to the lateral adjustment tab, making it possible to use this setup on any vintage Stanley Bailey or Bedrock plane. It took me a long time to get my hands on this one. It was out of stock for so long and is so once again. It’s only seen the honing stones once. $120 for the set
ECEmmerich block plane. Made in West Germany. I prefer metal planes. $65
I’ll attach some photos until I get frustrated with the program. Please PM me for more photos of each. I can email or text them to you much quicker than upload them here.
the photos look like they came out in this order from left to right
Stanley #5, Bedrock 605, Stanley smooth #6, Stanley #6 corrugated, Jackson saw, Bedrock 606C, Rob Cosman IBC Iron/CB, and ECEmmerich block plane.
located in Haddon Heights NJ. Will ship at buyers expense via PayPal or Venmo.
Thanks, Russ.