A Cordless drill for pilot holes...

[steven c newman]

Had to fire the little Hanson Drill...plastic gears. Looked through the tool cabinet for a better one to drill pilot holes with..
470467
I think this will do nicely...Goodell Pratt Co. of Greenfield, MASS. USA......a 1917 version of their No. 329 hand drill. 0-1/4" capacity, single speed ( Variable speed? How fast can you crank?) Reversing? Turn the crank the other direction. Solid wood handles..
470468
I figure the side handle is for when I have to pull the bit back out. The chuck has a Patent date: AUG 13, 1895....and is also by Goodell Pratt Co.

Plan is to use this for pilot holes, for when I install some hardware on a box.
470469
With screws, instead of nails...

Should do the job?

[Joe Tilson]

Works for me, and a lot less noise. Best wishes in your work.

[Jason Buresh]

Had to fire the little Hanson Drill...plastic gears. Looked through the tool cabinet for a better one to drill pilot holes with..
470467
I think this will do nicely...Goodell Pratt Co. of Greenfield, MASS. USA......a 1917 version of their No. 329 hand drill. 0-1/4" capacity, single speed ( Variable speed? How fast can you crank?) Reversing? Turn the crank the other direction. Solid wood handles..
470468
I figure the side handle is for when I have to pull the bit back out. The chuck has a Patent date: AUG 13, 1895....and is also by Goodell Pratt Co.

Plan is to use this for pilot holes, for when I install some hardware on a box.
470469
With screws, instead of nails...

Should do the job?

I have acquired quite a few of these drills. It makes me wonder why they ever fell out of favor. They require no batteries, they are lighter, and if you ask me they are more accurate because they are better balanced.

[Jim Koepke]

I have acquired quite a few of these drills. It makes me wonder why they ever fell out of favor. They require no batteries, they are lighter, and if you ask me they are more accurate because they are better balanced.

All but my two Millers Falls #2 models and a Goodell Pratt #5-1/2 have been sold or given away.

For small screws it is often my preference to use something even slower, easier to control, than an eggbeater to drill shank and pilot holes. A recent win on ebay brought home a lot of things including a 1/2" Millers Falls #810 countersink:

470518

It is now the best countersink in my accumulations of countersinks.

For boring without using an eggbeater my two 'straight' handles work great. Another recent acquisition is also great for control when boring shallow holes:

470520

The straight handles can be used between the hands like using a stick to start a fire if one wants some extra speed.

The Goodell Pratt #5-1/2 is a two speed drill. The slow speed turns the chuck a little more than one time for one revolution of the crank. That is handy for the bigger bits.

The brace chuck can hold regular twist bits or auger tanged bits.

The other holder is a tap holder that can also hold drill bits up to 1/4".

They all do a great job for controlled boring.

470519

Not sure where this chart originated:

470521

A little time was spent marking out the shank size and pilot hole size needed for the various screws. The size for gimlets was also added. This may be different for different makers of gimlets. These were the sizes marked on the tang of a lot of gimlets purchased on an ebay bid.

BTW, the chuck on my #5-1/2 has the same Aug 13, 1895 patent date > https://pdfpiw.uspto.gov/.piw?PageNum=0&idkey=NONE&SectionNum=3&HomeUrl=&docid=0544411

jtk

[steven c newman]

Ok...Had to set up a second drill, needed slightly larger holes drilled in the hinges, to clear these screws better..
470534
For scale? That HUGE screw is a #6 Drywall screw, 1-5/8" long, the screws I was using? 1 is resting IN the drywall screw's threads..Second eggbeater?
470535
One of the very few Stanley Handyman tools in the shop ( other one is a H1248)....wasn't too bad, drilling Brass.


Ready rack of drills IN the shop? The "main" rack..
470536
The brace off to the left..
470537
Is a Stanley 14" Holdall? Beside it is a PEXTO Samson 12" brace.

Over in the door?
470538
The HUGE eggbeater is a Millers Falls No. 2-01.

Hand drills..( non Millers Falls)..
470539
Figured these might be a bit too big for the job.

I size the tool to the job being done...YMMV...