View Full Version : design print out and digitize and plasma cut a metal sign
stan kern
07-27-2021, 10:37 AM
going to show tracing out the paper diagram and getting the file
ready for a plasma cut
Design print out and digitize and plasma cut a metal sign
https://youtu.be/qJfGxzLsSjo
David Buchhauser
07-28-2021, 12:59 AM
Nice work Stan! On another subject - can you cut steel with your 150W co2 laser cutter, and if so what is the maximum material thickness for mild steel you can cut?
Thanks,
David
stan kern
07-29-2021, 10:00 AM
no i cannot cut steel , I contract out my metal cuts
My shop cannot have a plasma cutter , it would be like smoking in a wood match box
David Buchhauser
07-29-2021, 7:27 PM
Stan - the reason I asked is that in one of your recent Youtube videos, you were duplicating a metal part by tracing and then cutting a duplicate with your 150W co2 laser. I thought you might be cutting some sort of fiber board, but wasn't sure.
Thanks,
David
https://www.youtube.com/watch?v=8EWtu2T5EqA
stan kern
08-04-2021, 11:46 AM
yes I could not get into the plasma shop (covid problems), so i used a black hardboard like a masonite its 1/8 thick
I just wanted to show the part fit
stan kern
08-04-2021, 11:48 AM
Also some metals do bother the drawing board tracing, so you might have to trace it with a pencil then digitize that pencil copy.
I have had good luck tracing most metals , once a crescent wrench would not trace out
Keith Outten
08-04-2021, 12:02 PM
Magnetism maybe? Not uncommon for tools to become magnetized in a variety of ways but you can make a coil and demag pretty easily.
stan kern
08-06-2021, 9:07 AM
never thought about magnetized, I have also read some florescent. light can interfere
Touch wood i have not had an issue like that
David Buchhauser
08-07-2021, 2:08 AM
Yes - the GTCO Calcomp drawing board/tablet is very susceptible to EMI noise from fluorescent lighting. My drawing boards will not work with the fluorescent lights turned on. I have both T12 and T8 and they both cause this problem. I had to install some LED tubes in the areas where I wish to use the boards, or else use in the daytime with natural light and the fluorescent lights turned off.
David
Keith Outten
08-07-2021, 7:43 AM
I use a florescent light, the base is about one foot above my drawing board so the lamp is about three feet above the board. I have not noticed any interference yet.
When I first installed my graphics board I placed my laptop on the surface, that was a definite no no.
When I was young I spent a lot of time doing magnetic particle inspection. We inspected parts as large as nuclear turbine disks down to very small fasteners. Plenty of weld inspection as well. Most of the time we were required to de-Gauss after inspection, especially if subsequent steps involved precision machining or parts that were to be installed near sensitive equipment.
David Buchhauser
08-07-2021, 5:15 PM
I have a small desk top fluorescent lamp that does not cause a problem. It is the 4 ft. T8 and 8 ft. T12 variety that have the large ballasts that put out all the noise - at least here in my shop.
David
Bill George
08-12-2021, 4:26 PM
I have a small desk top fluorescent lamp that does not cause a problem. It is the 4 ft. T8 and 8 ft. T12 variety that have the large ballasts that put out all the noise - at least here in my shop.
David
Are your light fixtures grounded?
David Buchhauser
08-12-2021, 5:45 PM
Are your light fixtures grounded?
Yes they are grounded.
David
stan kern
08-16-2021, 9:20 PM
https://logicgroup.vids.io/videos/449ddab61d1becc5cd/design-print-out-and-digitize-and-plasma-cut-a-metal-sign
the utube platform has been hacked not sure when it swill come back
David Buchhauser
08-16-2021, 9:41 PM
Stan - not sure why someone would "hack" your Vance Matsalla youtube channel, but you've still got your original here. Why not just put your videos on your own channel?
You might also want to go to the Plasmaspider site and change the links for the Vance Matsalla videos to your new locations.
David
https://www.youtube.com/channel/UCY0Pe_l7NFgMHsCSUTOaxzg/videos
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.