I need to figure out what to do with this

[justin byers]

Hello all,

So I’ve recently acquired two sets of beautiful quilted maple veneer panels. The bookmatches are 24” long and 18” wide and 7mm thick. I was going to resaw them into proper veneer and bang off some humidors, but they are just so beautiful that I’m doubting my plan. Any ideas?
448813448814

[Prashun Patel]

Make an electric guitar. Telecasters are straightforward if you've never done one before. Those are really spectacular pieces.

[George Yetka]

I would say make a couple frames out of something else and put these in them.

[justin byers]

They’re truly amazing. I’ve never made an instrument, that’s not a bad idea. I was honestly considering just framing them as art

[Brian Tymchak]

Wow! Amazing figure. Wish I had a source for stock like that.

I think I might feature that as door panels in a very special cabinet. If you can, definitely resaw to stretch the value of those pieces.

[Jim Becker]

Make an electric guitar. Telecasters are straightforward if you've never done one before. Those are really spectacular pieces.

Took the words right out of my mouth...and I'd be making multiples with that beautiful stock with a "less beautiful" body core!

[justin byers]

I’m kinda storming down the telecaster rabbit hole. Is there any books that would get me started on it? I’m a half decent woodworker, certainly not a rock star, and I don’t play guitar...

[justin byers]

Also, stock comes from unique woods of the NW. They have tons of gorgeous stock.

[Brian Tymchak]

Also, stock comes from unique woods of the NW. They have tons of gorgeous stock.

Thanks Justin!

[Jim Becker]

You will find a good level of resource in the TDPRI forum in the "Tele Home Depot" forum area. There's a sticky thread at the top with a good plan, too, although tele plans are very easy to come by with a simple search via Google.

[Prashun Patel]

The electric herald has plans. Now, beware, there’s a good deal of hardware to buy, so if you’re not into it, that can be a turn off; half of the project is fiddling with frets and strings and bridge heights. It’s all very doable and fun , but only if you are intrigued by making an instrument.

One bit of advice from the start: Telecasters call for a giant pickuguard which will cover your figure. Make yours withOUT a pickguard.

[Alan Kalker]

Find a reason to build a cabinet. These will make a fabulous door highlight. Use Maple for the rest of the cabinet to let these babies get all the huzzahs. Congratulations on your find.

[Myles Moran]

If you're not interested in fiddling with the frets and such, you can buy a prebuilt neck. I bought one from warmoth that was great quality and set up nicely with no adjustments. I also built a neck, glued on a pre-cut fretboard and paid a luthier to set my frets and cut the neck, and that was only a bit more expensive than the prebuilt neck.

[Prashun Patel]

Making the neck is so rewarding because it’s perceived to be very challenging to non woodworkers. But with an intermediate woodworker’s eye and tools it is straightforward.

[Jim Becker]

One bit of advice from the start: Telecasters call for a giant pickuguard which will cover your figure. Make yours withOUT a pickguard.

I solved that issue by doing a rear control cavity (with a cover the same size and shape as normal Tele control plate on the back) and no pickguard. Only my very first one had the pick guard. Controls are mounted through the wood similar to many other guitars.

https://snz04pap002files.storage.live.com/y4mTNUnPs974ddM5Pf-MLtb-IzUjwG9o0irisknRkm5WilC7EqJdUCwoKGeKntsP8IJvZH3RrC A1f6h3_KnJSxfN7Jf0PKr3Encrv7DqGaVRyQeaC7Mo_5vRp7qQ 7xOLEsQ6-GjjrD06z8C7ocq9xyLP88AhxSyTVujUKlXVeKmdKk0rL_1EieN vAQiE4Gicru1?width=660&height=660&cropmode=none

[Frank Pratt]

Whatever you make, please share. Those are outstanding. I think it would be a shame to cut them up to make small boxes (though they would be spectacular boxes).

[Myles Moran]

Making the neck is so rewarding because it’s perceived to be very challenging to non woodworkers. But with an intermediate woodworker’s eye and tools it is straightforward.

I definitely agree. I also enjoy having a well shaped volute at the end, and that's not readily available unless you're making it yourself.

That said, the first guitar I built had a neck like a baseball bat because I was afraid of getting the truss rod cavity too thin. My subsequent attempt was much better and the profile ended up with something very playable.

[Bill Dufour]

Consider donating it to a local college for their wood library. I have walked down the halls of the agriculture building at UC Berkely, Giannini Hall. They have off cuts of trees from around the world of all kinds of wood with labels screwed to the wall. The department started in 1868 and moved to the new building around 1912 so lots of stuff no longer available in huge old growth examples.
Bill D

[justin byers]

Well you’ve convinced me. I’m going to order a stew Mac tele hardware kit and template, and I think I’ll buy a warmoth neck for the first one, I’m sure I’ll make one eventually, but for the first I think I’ll buy one. I’m thinking sipo mahogany for the body and a dark neck, too bad we can’t ship rosewood necks to Canada. I’ve got a big ol board of Brazilian rosewood waiting for when I build my first neck, but until then... any more tools or things I’m gonna need?

[Myles Moran]

The only other tool that comes to mind is a soldering iron for putting the electronics together. Using a prebuilt neck means you shouldn't need metric or specific sized drill bits for the tuners. As for the neck connection, you'll probably want to have a self centering drill bit to get the neck attachment screws placed precisely. The rest of the build is just some quality time with the router, bandsaw, and sanding.

[Jim Becker]

If you want really easy for the electronics (pickups and wiring) GFS (GuitarFetish) has pre-wired harnesses and vary good pickup options that use their KwikPlug setup. There's zero soldering.

[Prashun Patel]

I think you should start a new thread here and on the other website called "My first telecaster build" You'll attract lots of helpful and encouraging responses.

I would plan out all the steps beforehand before cutting or shaping.

A spindle sander is really convenient for solid body guitars with their hard-to-access curves up around the neck and horns

Beware your templates from Stewmac. They call for a front route of the control cavity and the channel from the neck pickup to the control panel. YOU should do a rear mount control panel so you don't hide your wood. This makes mounting the controls a little more painful, but it's doable. You can also eliminate the pickup channel, but this will require a long drill between the 2 cavities. That is always a bear. I advise routing this channel in the middle ply of your body before gluing on the top plate or rear showcase plates.

Having a good template / pattern / flush trim router bit helps a lot. I invested in a couple from Whiteside at 1/4", 1/2" and 3/4" depth - the kinds with the bearing mounted closest to the shank. Then I have a long one with the bearing at the tip (sorry, top mounted/bottom mounted terminology confuses me...). The first ones are great for mortising.



Some other doodads you may need to order if not in your kit:

Nut (I got a Fender style tusq nut from Graphtec)
String trees
Knobs (there are a million Amzn. There are 2 types: CTS and Alpha; make sure they fit your POTS.
Switch harness: Jim's right about Guitar Fetish. Madhatter and Mojotone make pre-wired harnesses that avoid you having to solder. These come with the jack also wired.
Jack cup to mount the jack to the body.


Consider the kind of finish you want on it. Those beautiful veneers beg IMHO for a high gloss finish. You can rub out a good varnish or lacquer (if you have HVLP) with rubbing compounds and fine grit sandpaper.

Last, I highly recommend the videos on 'tube by Maximum Guitar Works. He does a whole Tele build and really outlines every step of the way. Very watchable.

Other great video resources are Crimson Guitar and Highline and Fletcher...

[justin byers]

That’s appealing for sure! I’ve got a buddy who’s an electrical engineer that was gonna help me, but that would be even easier. Is there a preferred template or will the stew Mac one do?

[Prashun Patel]

The ones from Stewmac will likely be perfect. I didn't mean to call them out in particular; many telecaster templates will have a top route channel and switch cavity.

[justin byers]

I actually didn’t see your other longer reply, thanks so much for the info. I’ve got more or less a professional level shop nowadays, obviously not luthier type things, but everything else. The rear mount controls are definitely the winner here to show off all that beauty quilt, and yeah most definitely gloss and high polished lacquer, I have a Fuji hvlp I’ve gotten pretty good with, and after all the humidors I’ve gotten pretty solid at polishing. Is there a template that would work better for rear mounted controls?

[Jim Becker]

You can use the same template...you just have to remember what gets cut on the front and what gets cut on the back. (the back obviously being flipped/reversed)

[justin byers]

Would it make more sense to just use a control cavity template on the back with one of the stew Mac covers that fits it? Sorry for all the questions, I know literally nothing about guitars. Also, rather than that slider switch, can you just use a standard toggle? Or is there some purpose to the sliding switch?

[Jim Becker]

If you want to use a pre-made control cover, then you'll want to use a template that matches it. I buy blank Telecaster style control plates (no holes) from GuitarFetish and do the recess on the back to match them exactly. You also have the option of making your own template for the control recess and making it out of wood, etc. Lots of options, but there's no rule that you must create a control cavity in a particular size/shape as long as it is the correct depth for the job and has enough space for the components intended to go inside. That said, if you are going to use a pre-wired harness that's intended for a Telecaster-type installation, sticking with something similar to what it would be on the front for spacing is a darn good idea...and the reason I do what I do: same size and shape, but on the back and a blank plate. Examples:

https://snz04pap002files.storage.live.com/y4mYgJSmaiQ6iIXk8ASVf6sGTwNZwNVnTNxTLzuFp8gxr9rzqT g98qefjr0rSKRevHxHRDcOIffg9hzRhILXZZnkseYfw-6jpWdFuo5jf_30r0HSZOfbFG7cDfLof-X9r1VzYGj7Q7LjyrIH57EnWuWh6xDytyWN0iLxmGas1QbCzAwK X3OHl6HpEZkAIkK1dlv?width=660&height=660&cropmode=none

https://snz04pap002files.storage.live.com/y4meQdHVnfmLvO6rV8DYqa2eaFeslyPDKpCU4MqO7H_9xaGm6i 7BmNCDm_dQdYsx4STOi0FSluQjLiTkoHlRIPcdwvFHCuNfjp2T pYL9ongF_f_UsATfbuNvG-mf2I-ndL8VH3lozeltWygjZkfKDeNM5nTqvVqfyDMW7iJUfp1rZTvlo UgUVt2lRO6wKRLHMLL?width=660&height=660&cropmode=none