Entry hall table for a niece: penultimate post

[Derek Cohen]

This is the last part of the build - completing of the drawer bottoms and pulls.


A panel was prepared some weeks ago. 1/4" thick Tasmanian Oak. This was made up of two, book matched boards. Blue tape was used to pull the jointed edges together. Clamps are unnecessary for this task ...


http://www.inthewoodshop.com/Furniture/EntryHallTableForANiece11_html_5222b26b.jpg


Measure off the full width of the drawer bottom from inside the slips ...


https://i.postimg.cc/05wh1q7q/2a.jpg


Of possible interest is the work holding for the drawer bottom ...


https://i.postimg.cc/85F9C23M/3a.jpg


The bench dogs on each side were made from sections of unhardened O1 steel, and filed into teeth.


https://i.postimg.cc/L5LWtzms/4a.jpg


Another heads-up is the arm for this cutting guard. Some while back, Veritas brought out a gauge with a fine adjuster. They now sell the arms to upgrade existing gauges, which is what I have done here to a wheel gauge I made ...


https://i.postimg.cc/HkpNMcRp/5a.jpg


Here the tongue is marked (about 4mm). This will fit into the groove in the slip.


The thickness of the tongue is marked (3mm).


https://i.postimg.cc/ZKPg0Ff7/6a.jpg


The tongue is planed ...


https://i.postimg.cc/Prn9tFMv/7a.jpg


The fit is tested with a spare slip ...


https://i.postimg.cc/tTLfnrQf/8a.jpg


The bottom was about 1mm too wide to fit. A LN edge was perfect to re-joint one side ...


https://i.postimg.cc/sgwN4fC5/9a.jpg


Re-establish the tongue with a shoulder plane ...


https://i.postimg.cc/BvbwYWJk/10a.jpg


Slide the bottom in. At this time it is just a dry fit. The front, which remains 1/4" thick to fit to 1/4" groove at the rear of the drawer front, is not yet pushed home. The front groove will hold the one end firmly, allowing movement towards the rear of the drawer.


https://i.postimg.cc/nV5qTPHP/11a.jpg

[Derek Cohen]

The drawers require pulls. The aim is to make the pulls "vanish" as much as possible. To do this, the shape is kept simple, and the wood is a section from the drawer fronts. Here it is being planed to 1/4" thickness.


https://i.postimg.cc/9fkgsxMM/12a.jpg


Set up to make the pulls ...


https://i.postimg.cc/50FKJwYm/13a.jpg


A 10mm wide rebate is planed on both sides. This will be completed on the reverse side as well, to create a tenon 3mm thick.


https://i.postimg.cc/3N5Sxd2Q/14a.jpg


Four sections are marked off for the pulls (only three are needed) ..


https://i.postimg.cc/BZH7wBGS/15a.jpg


A router is used to create dimples for a finger grip on the underside of the pull (three were needed and were good here; one could be tossed) ...


https://i.postimg.cc/6qrH2th2/16a.jpg


https://i.postimg.cc/VLwZy0Yj/17a.jpg


The outlines are cut out ...


https://i.postimg.cc/vZKHSsW6/18a.jpg


The router is again used, this time to create a 3mm x 50mm mortice in the drawer fronts for the pulls ...


https://i.postimg.cc/VNbsxVRZ/19a.jpg


The final section of the build is the drawer back. I decided to use Jarrah to match the rest - one never knows whether the hall table will become a room divider.


The newly-purchased JessEm Clear-Cut TS Stock Guides make a clean, accurate rip that much easier ...


https://i.postimg.cc/HxDWd9vY/20a.jpg


The next post will show the completed hall table.


Regards from Perth


Derek

[Scott Winners]

Of course you made a spare slip and a spare drawer pull.

I am coming around to 'liking' this drawer method more and more. A hundred years from now, three hundred years from now this piece will be fully restorable with some wood, some hide glue and sharp tools. Plus good judgement and astute common sense of course. Whoever gets the resto job will not have to replicate Brand W drawer metal pulls with dimensions x, y and z.

Is the fixed end of the unhardened hand toothed O1 tool steel workholder affixed to the top end of a dedicated bench dog so you can move it to whatever dog hole?

Thanks for posting. It has taken me 15 months of reading them to start to understand what you are doing.

[Oskar Sedell]

Thanks Derek for documenting your build with such clear pictures! Well done, and I´m looking forward to see the finished piece!

[Derek Cohen]

....
Is the fixed end of the unhardened hand toothed O1 tool steel workholder affixed to the top end of a dedicated bench dog so you can move it to whatever dog hole?..

Thanks Scott.

This is from my website two years ago (since then you can now purchase something very similar from Tools for Working Wood) ...

Make your own planing stop. This took about 30 minutes to make and install ...

http://www.inthewoodshop.com/ShopMadeTools/PlaningStop_html_mb904dd0.jpg

It looks like an ordinary dog hole. 1" wide in O1 steel. Filed 8 ppi. Sharp like a saw.

http://www.inthewoodshop.com/ShopMadeTools/PlaningStop_html_m3ec1ab60.jpg
The brass screws have been replaced by stainless steel M6 bolts into threaded inserts ...

http://www.inthewoodshop.com/ShopMadeTools/PlaningStop_html_m6718b583.jpg

This is the spring-loaded bench dog. It will remain at any height it is set. Note that all my bench dogs are exactly the same, and this one can be used in place of any other ...

http://www.inthewoodshop.com/ShopMadeTools/PlaningStop_html_1fa82952.jpg

How the stop looks to the wood http://www.inthewoodshop.com/ShopMadeTools/PlaningStop_html_7c1517e.gif

http://www.inthewoodshop.com/ShopMadeTools/PlaningStop_html_m13f6e1a8.jpg


Since all my dog holes are identical, I can switch them around. I made two of these: one for the tail vise and one for the stop.

Regards from Perth

Derek

[Derek Cohen]

Thanks Derek for documenting your build with such clear pictures! Well done, and I´m looking forward to see the finished piece!

Thanks Oskar.

Final pictures this weekend.

Regards from Perth

Derek

[James Pallas]

Well done Derek. I very much like your pulls. I like pulls that try to hide. I usually make drawer stops similar to your springs on your bench dogs. They work well. The only down side is people don’t expect them and sometimes do damage trying to remove the drawers. It’s worth the effort to explain their operations to the owners of the piece.

[Jim Koepke]

Thanks Oskar.

Final pictures this weekend.

Regards from Perth

Derek

It will be worth the wait.

jtk

[Mike Allen1010]

Thanks Scott.

This is from my website two years ago (since then you can now purchase something very similar from Tools for Working Wood) ...

Make your own planing stop. This took about 30 minutes to make and install ...

http://www.inthewoodshop.com/ShopMadeTools/PlaningStop_html_mb904dd0.jpg

It looks like an ordinary dog hole. 1" wide in O1 steel. Filed 8 ppi. Sharp like a saw.

http://www.inthewoodshop.com/ShopMadeTools/PlaningStop_html_m3ec1ab60.jpg
The brass screws have been replaced by stainless steel M6 bolts into threaded inserts ...

http://www.inthewoodshop.com/ShopMadeTools/PlaningStop_html_m6718b583.jpg

This is the spring-loaded bench dog. It will remain at any height it is set. Note that all my bench dogs are exactly the same, and this one can be used in place of any other ...

http://www.inthewoodshop.com/ShopMadeTools/PlaningStop_html_1fa82952.jpg

How the stop looks to the wood http://www.inthewoodshop.com/ShopMadeTools/PlaningStop_html_7c1517e.gif

http://www.inthewoodshop.com/ShopMadeTools/PlaningStop_html_m13f6e1a8.jpg


Since all my dog holes are identical, I can switch them around. I made two of these: one for the tail vise and one for the stop.

Regards from Perth

Derek

Derek, Great solution to what is is for me a consistent problem – work holding thin stock! Definitely stealing this idea – and blue tape for gluing up thin panels – who knew?

More importantly super enjoyed this entire build – as usual your pictures and descriptions are excellent and extremely helpful. I very much look forward to seeing the final result.

So when are you gonna start teaching classes? Can think of anyone more qualified and I know you'd be great at it.

Best, Mike

[Derek Cohen]

Thanks Mike.

I do run workshops every now-and-then (usually at wood shows). However, who has time to do this otherwise?

Regards from Perth

Derek

[Phil Mueller]

Been thinking of your solution for thin stock as well, Derek. I haven’t the occasion to do work with larger thin panels, so in the meantime, for smaller length/width pieces, I just made a quick planning board. The stops are slightly less than 1/16”. Works well for small stuff (BTW, I’m left handed, so this is likely backwards for most).

427844

I also just use tape for gluing thin panels/pieces, but have been using this 3M tape. Not cheap, but has a good stretch to it, sticks well, and comes off without much issue.

427845

Always good to see a few different methods.