Incra 1000HD Users Question

[John McKissick]

Considering this miter gauge but I have a real use question for real life users
The videos and specs seem to universally love this tool but as I look at the vernier cursor area it looks fragile to me sticking out like it does.

418531

Has anyone experienced issues with that?

I have a part time shop with safe storage but it's not full time for wood working shop and a smaller Bosch job site saw

[Kevin McCluney]

I've used one of these for years without any damage to the vernier scale.

[Steve Fish]

I just picked one up about a month ago. If it were to drop I think the track bar or a corner of the fence would hit the floor first. The thinnest piece is indeed that little cursor but it’s tucked into that corner pretty well The lever beneath it appears to be cut from the same thickness as the protractor. I would not worry about it all that much as long as you are mindful of your tools and Incra’s customer service has been very good in my (albeit short) experience should you need a replacement part

[Clint Baxter]

I've used one of these for years without any damage to the vernier scale.

Have also had one for years without any problems. It is pretty thin, but as stated earlier, fairly well protected in that location.

Clint

[tom lucas]

For years I looked at these without buying, thinking they didn't look all that sturdy. A few years ago I bought one. It's plenty sturdy. Love it. Don't hesitate. Just buy it. And I strongly suggest getting the adjustable fence/stop. A real nice upgrade to just about any other I've used.

[ChrisA Edwards]

I noticed the other day that the teeth for the 1 and 2 degree just left of the zero are damaged.

Not sure how I did this, not a huge deal as I rarely use those two indents, plus I think I could file those teeth back and still be able to access that setting if necessary.

The degree gauge can be purchased as a spare part, about $40, if necessary.

https://i1094.photobucket.com/albums/i452/cedwards874/Woodworking/INCRAHD1000amage_zpsuqc2uztd.jpg

[William A Johnston]

I've had one for a few years and use it often. I think the quality is excellent. Like any tool if you drop it there is a possibility it will damage.

That said I'd highly recommend buying one.

Bill

[Randy Heinemann]

The only way to damage it would be to drop on your shop floor (especially concrete). The fact is, though, you might be able to get by with one of the less expensive Incra models as there really isn't much call for the finest adjustments you can make on the HD. On the other hand, I suppose the HD is worth it if you even have one instance of a use for it.

[Prashun Patel]

I have not had issues with that. I have dropped mine once or twice. It’s pretty durable.

[Frederick Skelly]

No problems with that at all. Love that tool. The only drawback is that it's quite heavy (IMO).

[Brian Holcombe]

It’s a great miter gauge, but that part is delicate.

I hang my up when it’s not in use.

[John McKissick]

Looks like the tooth to the right is a bit rounded off too.


I noticed the other day that the teeth for the 1 and 2 degree just left of the zero are damaged.

Not sure how I did this, not a huge deal as I rarely use those two indents, plus I think I could file those teeth back and still be able to access that setting if necessary.

The degree gauge can be purchased as a spare part, about $40, if necessary.

https://i1094.photobucket.com/albums/i452/cedwards874/Woodworking/INCRAHD1000amage_zpsuqc2uztd.jpg

[John McKissick]

I have a cabinet to place when not in use. My concern is accidental abuse like dropping it. My 61 year old fingers are not 25 any longer, nuff said on that...

Thanks for your input


It’s a great miter gauge, but that part is delicate.

I hang my up when it’s not in use.

[Dave Cav]

I've had mine for ten years or so without any problems either. It stays hung up out of the way when not in use. However, it's not a tool I would buy for a school shop or probably a working shop with multiple employees running the table saw.

[Alex Zeller]

The teeth's job is only to make it easier when setting it to a whole degree (or to 22.5°). Like any other miter gauge you lock it in place by tightening the handle. I have mine set so I don't use the teeth at all. The vernier cursor touches before the arm with the point that locks into the teeth. But I only use mine to make cuts that are unusual angles for multi-sided boxes and segmented bowls. I have the adjustable fence that came with it on the miter gauge that came with my saw. I leave that one set to 90° and rarely check it.

As far as damaging it goes, the arm with the pointer is pretty stout. In general I would be careful with it no matter what. With anything that's precision you want to be careful. If you have a T-slot it'll help as it's not likely to fall off the saw. It's when you remove it and in a hurry you set it somewhere that's not as secure as you think that you should avoid. That's one of my weak points so I make it a point not to do it with expensive or accurate tools. I haven't yet but I'm thinking of making a way of holding it on my saw. Not sure if I'll make a slot for it to slide into or something to hang it from.

[ChrisA Edwards]

I know I posted the photo showing the damage to a couple of teeth, but I do want to re-iterate, I love this miter gauge and I would repair or replace it if necessary.

Mine lives here when not it use.

https://i1094.photobucket.com/albums/i452/cedwards874/Woodworking/SawStop/SE4_zpsvyjcexpb.jpg