Travel mug liner source??

[Ricc Havens]

I've been making travel mugs off and on for a couple years now. Due to my limited disability income I had been buying the travel mugs from Hobby Lobby or Micheal's with the plastic liner and stainless insert for usually $2.99-$4.99 as an affordable option compared to the $12-$13 they cost from other woodworking suppliers. The plastic liners are easily removed and the steel liner is ready to use.

Lately none of the local Hobby Lobby, Michael's, or Christmas Tree Shoppe store are currently carrying them. I have an order to make a few and I have a couple upcoming christmas craft shows that I can usually sell some at. But in my area at crafts shows the going rate is around $35-$40. So, the $12-$13 dollar cost eats in to what little profit is possible.

Are any of you getting travel mug liners from other affordable sources?

Thanks
Ricc

[Sam Force]

I get mine from discountmugs dot com. Item ST33

[Greg Just]

I also get mine from Discountmugs. Like you said, remove the plastic liner and you're ready to go. Make sure you buy enough to get the shipping waved or your cost goes way up.

[Chris A Lawrence]

How hard is it to get the plastic liner off them?

[Greg Just]

How hard is it to get the plastic liner off them?

There is a small screw on the bottom that you must remove. Sometimes I have to heat the plastic liner to loosen it from the liner and I do this with a heat gun (paint gun from Harbor Freight) and this only takes a few seconds. In addition, there is a rubber gasket attached to the liner that I remove.

[Mike Goetzke]

I've never made these but remember some mentioning going to Walmart for travel mugs and harvesting the liners.

Mike

[Ricc Havens]

How hard is it to get the plastic liner off them?

Chris, it's easy. Remove the screw on the bottom (usually hidden under a thin layer of rubber). Instead of using a heat gun like Chris (as I don't have a heat gun) I roll the top lip of the cup just below the steel rim along the edge of my workbench. With a little pressure as your roll the plastic will crack and you will be able to pull the liner off.

[Ricc Havens]

I get mine from discountmugs dot com. Item ST33

Thanks Sam and Greg! I'll check them out. If anyone has other sources let us all know.

[Ben Darrah]

I do a similar method as you and get mine at Big Lots. Website shows they have one in Elkhart.

[Ricc Havens]

I do a similar method as you and get mine at Big Lots. Website shows they have one in Elkhart.


Forgot to include them in my original post. I had checked two area Big Lots and had no luck. THANKS!

[Steve Mellott]

If you only need a few, you may want to periodically check the local Goodwill or Salvation Army store. I have found mugs in excellent condition for $1 - $2 each. After you remove the screw on the bottom, you have what you need.

[Ricc Havens]

If you only need a few, you may want to periodically check the local Goodwill or Salvation Army store. I have found mugs in excellent condition for $1 - $2 each. After you remove the screw on the bottom, you have what you need.


Steve, thanks for the input. In the past I have checked Goodwill and garage sales. But, usually find that the lids show signs of use like small dents in the steel lip or scratches, or the rubber seal around the lid is very worn. So I don't want to make one to sell at craft shows or give as a gift if it looks used.

[Dean Thomas]

Have you tried eBay??

[Ricc Havens]

Have you tried eBay??


Dean, I did check Ebay. But the only "kits" I could find were still $10 or more. The individual plastic mugs with stainless liners can be found on Ebay but I didn't see any that you could buy in quantities. About all I saw were single unit sale listings for mugs with some sort of log people thought might have collector value and they were usually $4 or more plus shipping for each listing. So that would get expensive.

Thanks for the idea.