Its here...

[Marshall Harrison]

My Laguna Fusion F2 table saw was delivered a few minutes ago. But you will have to take my word for it as most of the pictures are stuck on my iPhone. I'll post them once I can convince my MacBookPro to talk with to my iPhone instead of just beeping .


384195

[Larry Edgerton]

Good for you. Looking forward to your impressions as I have not seen one.

[Marshall Harrison]

Good for you. Looking forward to your impressions as I have not seen one.

I'll provide my impressions as I proceed tomorrow morning. I want to have both of my sons here to help. That bugger is a beast.

Only impression I have at the moment is that they sure used a lot of nails in the shipping crate lid. :D

[Dave Cav]

Only impression I have at the moment is that they sure used a lot of nails in the shipping crate lid. :D

Minimax is the same. When my bandsaw showed up I figured I just scored a bunch of utility lumber too, but after dealing with all the nails there wasn't a single usable board left.

[Mike Cutler]

Congrats.
It looks like a nice table saw. Have fun with your sons getting it up and running.

I'd rather it be "over crated", than "under crated". ;)

[Bruce Page]

Congrats Marshall! I think you'll enjoy that saw for many years to come.

[Marshall Harrison]

OK. The saw has been setup and I've made both a rip and a crosscut. Both came out very clean with no burn marks and no binding issues. It also passed the nickel test. Only two small issues. The right side wing had to be adjusted but the left side was dead on from the factory. Only other problem is the fence doesn't slide as smoothly as I would hope but I'll keep fiddling with that. IT does lock down square to the blade etc.

I'm a happy camper now. Picking up some wood and a jointer tomorrow. Still need to clean out the garage some and figure out tool placement.
384263
384262384264384265384266

[julian abram]

Very nice, now get some sawdust on so it's not so shiny and new looking!

[Bruce Page]

I had to install both wings on my Unisaw when I set it up..
Put a good coat of paste wax on the top. I'll give some rust protection and help the fence as well as the wood slide smoother.

[Marshall Harrison]

I had to install both wings on my Unisaw when I set it up..
Put a good coat of paste wax on the top. I'll give some rust protection and help the fence as well as the wood slide smoother.
I like the fact that the saw came with the wings installed as that really simplified things. Already got a coat of wax on it and I will add another coat or two before I finish.

[Charlie Hinton]

Always nice to get a new tool.
Enjoy it.

[Steve Rozmiarek]

Thats cool Marshall! I've not seen one in person, curious about the fence, is it a Biesmeyer clone, pics?

[Marshall Harrison]

Thats cool Marshall! I've not seen one in person, curious about the fence, is it a Biesmeyer clone, pics?

Yes, its a t-square Beisemeyer clone. Pretty substantial too. I'll see about getting some pics for you.

[Marshall Harrison]

Fence pics as promised for Steve. I had a similar fence on the Sears Zip Code saw I had 10 years ago but this is the best fence I've had on a table saw.

384378384379384380

[Charlie Jones]

Nice saw Marshall. I am impressed with Lagunas quality of late.

[Steve Rozmiarek]

Fence pics as promised for Steve. I had a similar fence on the Sears Zip Code saw I had 10 years ago but this is the best fence I've had on a table saw.

384378384379384380

Oh yeah, I like it! Aluminum tube or phenolic faces? I can't quite tell on my phone screen.

[Marshall Harrison]

Oh yeah, I like it! Aluminum tube or phenolic faces? I can't quite tell on my phone screen.

Aluminum tube. Not sure which I would prefer as I have never had phenolic faces.

[Frank Necaise]

Nice new saw. Let us see its first use too.