glenn bradley
02-08-2018, 8:12 AM
This jig had appeared in use or in the background of a pic during another thread. Lee Schierer asked to post more about it so, here we go. This is based on the version in ShopNotes #76. the primary difference being that I use an 'edge guide' clamp instead of their threaded rod solution for clamping the jig to the material to be cut.
Another modification I made to my dado jigs back in 2006 was to add a rabbet on the reference edge. This allows the router to reference via a template as opposed to via the outer edge of the router plate. This makes router orientation a non-issue (assuming you've centered your template collar and plate) and makes the jig smaller and therefor lighter.
I use featherboards and the router table to cut the large rabbet that will accept the edge-guide-clamp.
378612 . 378611
The cross arms are your fence and so must be true. I glue them, dialing them in for 90* and then clamping. Once the glue is set I add screws for strength.
378614
I had to grind a bit off of the flat head 1/4-20 screws I will use to attach (and adjust) the clamp. your screws or bolts will depend on your choice of edge-guide-clamp.
378613
Let's call the part of the jig that the clamp is on the 'small jaw'. What doesn't show well here is the slots that allow the 'large jaw' to adjust. I will add that pic in the next post. At any rate, you end up here. The edge guide is positioned so that when its moving jaw is fully engaged, it is even with the jigs near-end cross arm. This near-end cross arm is your reference edge against your material to square the jig. So, slide the cross arm up against the edge of your material, slide the jig over so that the slot is dead-on your desired dado location and lock the clamp.
378615
Like other such jigs, the width is set "auto-magically" by clamping the material that will go into the dado between the jaws. This is done prior to positioning the jig on the material to be cut.
378616
Here is a picture showing the underside prior to my removing some unneeded material from the large jaw in order to further reduce weight.
378618
And here is the unit in use. You can see the large jaw is now not quite so large due to the removed material.
378617
cont'd
Another modification I made to my dado jigs back in 2006 was to add a rabbet on the reference edge. This allows the router to reference via a template as opposed to via the outer edge of the router plate. This makes router orientation a non-issue (assuming you've centered your template collar and plate) and makes the jig smaller and therefor lighter.
I use featherboards and the router table to cut the large rabbet that will accept the edge-guide-clamp.
378612 . 378611
The cross arms are your fence and so must be true. I glue them, dialing them in for 90* and then clamping. Once the glue is set I add screws for strength.
378614
I had to grind a bit off of the flat head 1/4-20 screws I will use to attach (and adjust) the clamp. your screws or bolts will depend on your choice of edge-guide-clamp.
378613
Let's call the part of the jig that the clamp is on the 'small jaw'. What doesn't show well here is the slots that allow the 'large jaw' to adjust. I will add that pic in the next post. At any rate, you end up here. The edge guide is positioned so that when its moving jaw is fully engaged, it is even with the jigs near-end cross arm. This near-end cross arm is your reference edge against your material to square the jig. So, slide the cross arm up against the edge of your material, slide the jig over so that the slot is dead-on your desired dado location and lock the clamp.
378615
Like other such jigs, the width is set "auto-magically" by clamping the material that will go into the dado between the jaws. This is done prior to positioning the jig on the material to be cut.
378616
Here is a picture showing the underside prior to my removing some unneeded material from the large jaw in order to further reduce weight.
378618
And here is the unit in use. You can see the large jaw is now not quite so large due to the removed material.
378617
cont'd