PDA

View Full Version : I have a friend who....



Ken Fitzgerald
01-26-2018, 7:14 PM
would like to know how long it takes to wear Gorilla glue off your hands?

:o

He might have been building a turning blank storage rack in my shop today.:o:rolleyes:

Stephen Tashiro
01-26-2018, 8:01 PM
A friend told me about 2 weeks.

Ken Fitzgerald
01-26-2018, 8:03 PM
Thank your friend for me!:D

Jim Becker
01-26-2018, 8:06 PM
Your "friend" should just wear greasy overalls and chew on a piece of straw and nobody will notice the black glue... :) :D

Perry Hilbert Jr
01-26-2018, 8:51 PM
unsure about ape glue. found out through a scientific study that CA glue takes 4.7 days to peel off of left hand fingers. Told the darn assistant to leave me apply the glue. that I intended to put nitrile gloves on first. Instead.. she shakes the vial after removing the lid and droplets go everywhere. Still a spot on the leather stool cushion. You'd think an RN would know better.

Lee Schierer
01-26-2018, 9:12 PM
I find that I can remove it before it sets with a rag and some lacquer thinner in a few seconds. Once it cures you are looking at at least a week.

Jim Becker
01-26-2018, 10:20 PM
Perry...you can also use CA glue remover which is much faster than wearing the CA off. :) Unfortunately, the Gorilla Glue leaves a black stain on flesh...not pretty. Lee's idea sounds pretty good.

Jim Koepke
01-27-2018, 2:32 AM
Instead.. she shakes the vial after removing the lid and droplets go everywhere. Still a spot on the leather stool cushion. You'd think an RN would know better.

Saw something similar to this in a restaurant but it was a waitress with a ketchup bottle with a loose cap and a customer with a white shirt.

jtk

Keith Outten
01-27-2018, 11:04 AM
It took me about a week to get my thumbprint back recently. I was prepping some pen blanks and got Gorilla glue on my thumb and I thought I had wiped it off completely but I didn't get it all. For a week I couldn't use my thumbprint to get into my iPad of my iPhone :)

Stephen Tashiro
01-27-2018, 12:18 PM
I find that I can remove it before it sets with a rag and some lacquer thinner in a few seconds.

And if you don't have acetone handy, the best thing to do is wipe the glue (somewhat) off with a DRY cloth or paper towel. Washing with water or using a damp cloth makes Gorilla glue set faster.

Ken Fitzgerald
01-27-2018, 12:50 PM
"My friend" was assembling a frame that used horizontal and vertical cross-members that interlocked using half-lap joints. Because the vertical member had to interlock with 3 horizontal members simultaneously, he had to put glue on all 3 joints at the same time and then begin screwing the joints. Thus, his left hand has more Gorilla glue on it than his right hand which was holding the racheting impact driver. So when he went to supper last night with his wife, he kept his left hand under the table most of the time.

Mel Fulks
01-27-2018, 1:09 PM
I predict ...that modernized historical texts will soon use "Gorilla Glue" to replace "leprosy".

Doug Garson
01-27-2018, 1:34 PM
Does "your friend" know you are publishing all his embarrassing stories on a public forum? If you're not careful he may start telling tales about you.:p

Ken Fitzgerald
01-27-2018, 2:10 PM
Does "your friend" know you are publishing all his embarrassing stories on a public forum? If you're not careful he may start telling tales about you.:p

He does. Yet, I have a hard time imagining losing him as a friend.:p

Tony De Masi
01-28-2018, 6:27 PM
Ken, your friend and my friend have much in common. Yesterday mine told me that he CA glued his wedding ring to his finger. I told him to go get some nail polish remover from his wife and that should help. I also told him to write a note to keep some debonder on hand too.

Jim Becker
01-28-2018, 8:02 PM
It's so nice to see that everyone has so many "friends"... :) :D :p

Stephen Tashiro
01-28-2018, 8:47 PM
"My friend" was assembling a frame that used horizontal and vertical cross-members that interlocked using half-lap joints. Because the vertical member had to interlock with 3 horizontal members simultaneously, he had to put glue on all 3 joints at the same time and then begin screwing the joints..

Some of our friends might be interested in how to get Gorilla glue off of screwdrivers and other tools.

Ken Fitzgerald
01-28-2018, 10:30 PM
The only Gorilla glue on my friends 18v Makita driver was in 2 vent holes. My friend removed it before going to the house to try to clean his hands. He removed it by fingering a woodscrew into the glob of glue and then pulling the screw out. I hope my friend doesn't mind me telling his recovery secretes.:rolleyes: