Saw Bench - Photos

[Brian Holcombe]

Hi all,

I received a PM requesting photos of my saw bench, the photos in my thread dedicated to building the bench were all hosted on a website which no longer allows one to post them to message boards for free.

So, these are hosted on my website, which I already pay for. :D

Most of what I've built for workshop fixtures are borrowed and modified to suit my purpose. If anyone decides to build a bench similar to this one, I suggest make the base a little heavier and feet a little wider. I'd also make this shorter because I don't need the length with Japanese saws.

https://brianholcombewoodworker.com/wp-content/uploads/2018/01/IMG_9161.jpg
https://brianholcombewoodworker.com/wp-content/uploads/2018/01/IMG_9160.jpg
https://brianholcombewoodworker.com/wp-content/uploads/2018/01/IMG_9162-930318497-1515605909124.jpg

[Prashun Patel]

Nice bench. I thought it was a mortise-chopping bench ;)

Nice chair back there.Too bad you didn't take SMC on the journey of iteration on that one. There's a lot of learning ala Michael Fortune in that design. I say that not to imply design similarity, but your process and careful thinking in making the process economical and repeatable. It's been a treat.

[Pete Taran]

Not sure what is more impressive, the bench and chair, or the carpeted shop! Very spiffy!

[Phil Mueller]

Brian, your shop furniture is clearly built to a standard of fine home furniture. That would look just as nice as a convenient bench anywhere in the home. Nicely done, as usual.

Not for comparison, whatsoever, but I built this design.
375949

My only regret is that I did not make the center opening wide enough to accept clamps. And the way this is designed, it would not be easy to increase the gap at this point. So since this picture was taken, I have resorted to a few dog holes.

[Stew Denton]

Brian,

+1 on what was said above. Beautiful work, and very functional as well. Super project!

Stew

[Brian Holcombe]

Nice bench. I thought it was a mortise-chopping bench ;)

Nice chair back there.Too bad you didn't take SMC on the journey of iteration on that one. There's a lot of learning ala Michael Fortune in that design. I say that not to imply design similarity, but your process and careful thinking in making the process economical and repeatable. It's been a treat.

Most often it is :D I'm glad you have enjoyed following along with it! I have been debating how much I will release, I do plan to put out some information but of course in a blog post. It's been a long process, as you know, so I've been dying to tell the story.


Not sure what is more impressive, the bench and chair, or the carpeted shop! Very spiffy!

Thanks Pete!


Brian, your shop furniture is clearly built to a standard of fine home furniture. That would look just as nice as a convenient bench anywhere in the home. Nicely done, as usual.

Not for comparison, whatsoever, but I built this design.
375949

My only regret is that I did not make the center opening wide enough to accept clamps. And the way this is designed, it would not be easy to increase the gap at this point. So since this picture was taken, I have resorted to a few dog holes.

Thanks Phil! I think that bench looks better than it really is, it's plentiful with warts. Like most things it takes an iteration or two before you really iron out everything that you like and dislike. I know for some of the things that seem very simple they can often take more still.

[Christopher Charles]

Thanks for posting Brian! Your carpet is still looking good :)

Best,
Chris

[David Eisenhauer]

Good looking bench, but how thick are the tops? Heavy little devil? You say that it could use a wider base - could that be due to being used on a carpeted floor or is it just a little unstable anyway? The feet look to be just about as wide as the top. I like the through M&T on the top connection as I have been working on some of those in 2-1/2" material lately. Plus 1 on more chair info please. That is a beauty.

[Pat Barry]

That anvil is awesome, as is the Shoji work. I love the character in the panel behind the anvil.

[Rob Luter]

That bench is fantastic. I'd be afraid to use it for fear of marring it if the saw slipped or my alignment was off.

[lowell holmes]

Show off:)

[Brian Holcombe]

Thanks Fellas!

David, yes it could be slightly wider. I'm sure I opted not to do that because I did not want the feet wider than the top. Carpet likely making it worse. The top is 8/4 material, so probably 1-7/8"~