wooden plow plane

[Gerald Schram]

receivedthis plane from sil , she bought at estate sale. the depth stop fits very tight in its mortice i think thats why the brass plate the adjuster goes though broke in half. would you file the adjuster or the mortice to fit better? while the plane was probable was made around 1860ish { judging from the screws} i just want to put the plane back to work. thanks for any thoughts jerry

[Stewie Simpson]

Its the wooden stock that's likely moved. I would focus on the mortise.

[Derek Cohen]

Hi Gerald

Check if the brass adjuster is running freely now that it is out of the plane body. I suspect that the depth stop runs inside a brass casing. If so, all that needs to be done is clean and oil it internally. The wood for the mortice may have moved, as Stewie has commented, but the fix may not lie with the mortice.

As I recall, the brass collar is important as it forms a garter to hold the screw in place. It may be sufficient to just screw the two sides down. If not, it may nee to be silver soldered or brazed.

Regards from Cape Town

Derek

[Gerald Schram]

i have a bit of 1/4" brass i was going to make a new plate it fits in between the thumb screw and a piecethats pinned to the threaded rod. i think i can drill out the rivet to slid the plate in place. i love the way the maker dovetail the brass to the skate. the adjuster runs freely now but the brass block is still tight in the mortice. thanks for the tips jerry

[Mike Allen1010]

Jerry, definitely a beautiful tool. I applaud your efforts to put it back to work.


With regard to your questions about best ways to solve your current problem, I completely defer to Stewie and Derek who know far better than me.


My reason for commenting is twofold;


A) Vintage wooden plow planes are among my favorite old tools; IMHO a still elegant solution to a fundamental woodworking task.


B) Any picture with shotgun shells in the background immediately gets my attention; are there birds around here? Where are the dogs?


Cheers, Mike

[Derek Cohen]

It has just occurred to me (I am away on vacation, along with my mind) that I built a plough plane and slotted this mechanism into it. From my website ...

Progress picture …
http://www.inthewoodshop.com/ShopMadeTools/BridlePloughBuild_html_397a27f.jpg




Fitting the depth stop. This came off the Mathieson parts plane.


First drill …
http://www.inthewoodshop.com/ShopMadeTools/BridlePloughBuild_html_m1311ae69.jpg




Then chisel …


http://www.inthewoodshop.com/ShopMadeTools/BridlePloughBuild_html_68062b50.jpg


http://www.inthewoodshop.com/ShopMadeTools/BridlePloughBuild_html_m3383810d.jpg


The upper side of the depth stop houses the adjuster …


http://www.inthewoodshop.com/ShopMadeTools/BridlePloughBuild_html_m283c5a9e.jpg

The brass cassette is a self-contained part, as I mentioned earlier. Any stiffness in adjustment will be within it, so keep it lubricated. You can also see the brass collar as a one piece section.

If you are needing more reference, the build is here: http://www.inthewoodshop.com/ShopMadeTools/BridlePloughBuild.html

http://www.inthewoodshop.com/ShopMadeTools/BridlePloughBuild_html_m4eb20c71.jpg

Regards from Cape Town (back in Perth tomorrow)

Derek

[Jim Koepke]

Any picture with shotgun shells in the background immediately gets my attention

Spent shotgun shells are good source material for chisel ferrules.

jtk

[Pete Taran]

Especially nice AA hulls like those that are actually made of brass.

[Gerald Schram]

thats a stunning looking plane derek! is that she oak?

[Gerald Schram]

Jim never thought of that. only have about 500 emptys waiting to be reloaded

[Derek Cohen]

thats a stunning looking plane derek! is that she oak?

Thanks Gerald. It is She-oak. A very dense and interlocked hardwood from Western Australia.

Regards from Perth

Derek