Flameup- 3 Cornered

[Roger Chandler]

367018
Had not posted any work in a while, so this one is interesting because of the flame in the box elder, and it is 3 cornered. It is 8" wide and 6" tall, and has a more refined finish in person, as it was wet sanded with antique oil, thinned with MS, then several finish coats of satin WOP were added, and when held in the hands the light reflects off it nicely.

I took the pic with my ipad, handheld, and it appears to not have captured the finish as well as I would have liked, but it is an okay pic, and quickly done without having to do much setup of my photo booth, etc.

Comment always welcome! :)

[Damon McLaughlin]

Very well done Roger. I love the shape and the red really just pops out.

[Bob Bergstrom]

Really nice idea and well executed. Nothing ever beats holding a piece and viewing it in person.

[Brice Rogers]

Very nice, Roger. I'm curious how large the cube was when you first mounted it on the lathe.

[William C Rogers]

That is a good looking. I really like everything abou it.

[Sid Matheny]

That is a super first rate piece Roger. Very well done!

[John K Jordan]

Had not posted any work in a while, so this one is interesting because of the flame in the box elder, and it is 3 cornered. It is 8" wide and 6" tall, and has a more refined finish in person, as it was wet sanded with antique oil, thinned with MS, then several finish coats of satin WOP were added, and when held in the hands the light reflects off it nicely.

I took the pic with my ipad, handheld, and it appears to not have captured the finish as well as I would have liked, but it is an okay pic, and quickly done without having to do much setup of my photo booth, etc.

That is nicely done and beautiful wood. Turned from a cube?

Your photo would probably show the satin surface sheen if you added some light coming from the front, perhaps a lower light or two (to the side or sides), not too bright, diffused with a piece of thin tissue on the front. Or even hold a piece of white paper to reflect the light or the least shiny side of crumpled and straightened aluminum foil as a poor man's soft reflection screen.

JKJ

[Roger Chandler]

Very nice, Roger. I'm curious how large the cube was when you first mounted it on the lathe.

To be honest, Brice, I did not measure the thing. It was a gnarly piece of box elder, cut at at an angle on one end, and it had a couple of bark inclusions folded into the wood, and a vine on top of that. I just put it on the bandsaw, and began to cut, turn, cut some more, until I got it where I thought I could get most of the bark inclusion and vine out of the blank, and what was left I could turn away, depending on how I oriented the blank on the lathe. I just adjusted the saw fence as I went along, and didn't pay attention to the measurement.

[Doug Herzberg]

Very nice piece, Roger.

[Roger Chandler]

Muchos Gracious, everyone! :)

[Roger Chandler]

Turned from a cube? JKJ
It is turned from a cube, John, I just don't remember the size of the cube, but the finished bowl is 8" across and it is 6" tall.

[David Delo]

A real eye catcher Roger, well done for sure.

[Thomas Wilson80]

I'm pretty new to turning, would you mind briefly describing the procedure to get the equal three points? I'm not sure I can imagine how it is done.
Thanks.
Beautiful work, btw!

[Roger Chandler]

I'm pretty new to turning, would you mind briefly describing the procedure to get the equal three points? I'm not sure I can imagine how it is done.
Thanks.
Beautiful work, btw!Tom, begin with a cube of wood, placed between centers on opposite corners [I cut the corners off]. Then, turn a tenon on one end, put in chuck and turn outside paying close attention to the ghost shadows, and watch those fingers.....you can hurt yourself! I do the outside first, like any bowl, the go to hollow out the inside. The inside is more problematic for knuckle busting.....:eek:

[Thomas Wilson80]

Thanks! This forum has been so helpful - I've really appreciated everyone's willingness to share and help.

[John K Jordan]

Thomas,

There are several ways to make these and a lot of info on the web. Here is the first one I found: http://avwoodturners.org/downloads/three-cornered-bowl.pdf

I made one once by making two from contrasting woods, one small, one large, and joined them so the small one made three feet for the larger one. Good fun!

JKJ

[robert baccus]

That is the most beautiful fantastic bowl I have seen in years. The shape is really tough and BE is soft and weak --very hard to cut smooth when dry. As they say in LA.--you done good yeah. Did a small one with a hollow dome in the middle and never did get the inside of the wings perfectly smooth.

[Roger Chandler]

That is the most beautiful fantastic bowl I have seen in years. The shape is really tough and BE is soft and weak --very hard to cut smooth when dry. As they say in LA.--you done good yeah. Did a small one with a hollow dome in the middle and never did get the inside of the wings perfectly smooth.That is very kind of you to say, Robert......thank you much!