Buying a used DJ-20

[Thomas Hutson]

Im Buying a used Delta DJ-20. The guy is asking 825 for it. He said he was firm on the price and that the machine is in great shape and makes good edges but he did say the infeed table has a slight cup to it along the length of the table with high points about 3 inches in front of the cutter head and 4 or 5 inches from the edge of the table. He initially did not tell me these things so I had assumed everything was good and agreed to buy it before I knew about it. I assumed everything was good to go and then he mentioned these things to me. He has been forthcoming since and has sent multiple pictures as hes 100 miles away. He said the cup is about the thickness of a piece of notebook paper. It was originally a 3 phase unit and that his father had installed a new delta motor and switches. There appears to be an electrical box on the right side of the stand with what I am assuming is a vfd or something else to get it to run on 240v which would mean that it is not a new motor etc. My question is should I pass on this jointer? He said it includes a brand new set of blades and the surfaces are clean ie no rust or anything. My concern is that maybe it was lapped by someone at some point because of rust or something and that has caused the cupping. is this something that I should pass up on?

Thanks,
Thomas

[Thomas Hutson]

365601365602365603365604365605365606here are the images he sent

[David Kumm]

Hard to say without putting a straight edge on it but lots of jointers have tables with a high end or on both ends. .004 is no worry, .008 gets high. The hollow along the length on the infeed end is not so bad if the table is flat across the width , particularly in front of the head. Outfeed is more critical. The area where the insert meets the cast iron tends to be a problem area but again, moreso on the outfeed. If the fence doesn't have twist, I'd run a board and see if I could live with it. I'm guessing the flaw isn't fatal. Dave

[Thomas Hutson]

another question i had was im going to have to drive 120 miles and rent a trailer to pick this up. at that point should i just look into a new grizzly? 0490?

[Andrew Hughes]

Since he's not using a precision straight edge the photo says nothing.

[Thomas Hutson]

Where would you get a precision straight edge from? and say the infeed isnt as flat as he says what could one do to flatten it if say he gave me alot cheaper price on it?

[Andrew Hughes]

Lee valley sells them and they are good.The one I bought from suburban tools is better.
If your set on buying a jointer with tables that can be adjusted like the DJ might as well get a precision straight edge.
Its in your advantage to buy a jointer that you can check with a straight edge before buying.
A precision straight edge need to be handled and cared for properly to stay straight and be useful.

[David Kumm]

If you can borrow a good straight edge, take it to Lowes or HD and check their extruded levels. I have a Penske 8' straightedge and found my 8' level was good enough to use on my jointers. They will tell you enough if as long as both tables to make a decision. I would not bet that a new machine would be better unless you get lucky. The tolerance specs are often pretty loose. Humps are far worse than hollows on the infeed side. Flat on the outfeed and co planar tables are most important. Dave

[William Chain]

I'm off to purchase a used DJ-20 tomorrow myself. How big a deal is it to find the knife setting jig?

[David Kumm]

You generally don't want a jig to set a jointer. One of two dial indicators set on the outfeed is way better. If you don't like that, buy ESTA holders and knives and set them once. Dave

[William Chain]

You generally don't want a jig to set a jointer. One of two dial indicators set on the outfeed is way better. If you don't like that, buy ESTA holders and knives and set them once. Dave

Well, its home. I got the tables all cleaned up, and they're bang-on flat. The fence squared up nicely. The knives are serviceable if I avoid the inch closest to the fence, but they'll get swapped in the future. Just gotta get everything dialed in now. Thanks for the knife setting advice. I also managed to come home with a little partner for the DJ-20 in the same deal. That one needs a bit more cleaning, but its in great shape....

I also came home with a bonus item, a feeder. But I'm not sure how to attach this guy.

(and I'm aware that the images are fubar)

[David Kumm]

Brian Lamb makes an indicator that i prefer over the Oneway to set knives. check his site. Dave

[William Chain]

Will do sir, thank you!

[Andrew Hughes]

Nice score William.:)

[Phillip Gregory]

I also came home with a bonus item, a feeder. But I'm not sure how to attach this guy.



The middle tire on the feeder is chewed up, so you will need to replace that first.

You would drill holes in the table of the machine you want to use the feeder on and then bolt the feeder's base to the table. Feeders aren't typically used on jointers but they are absolutely indispensable for a shaper and can be handy for ripping on a 3+ hp cabinet saw or ripping/resawing on a larger bandsaw.

[Cary Falk]

Western Roller is a great company to get feeder rollers from.

[William Chain]

I noticed the tire and found a source for replacement, but I'm contemplating putting this on the classifieds.... the price may well be come show me how to properly set new blades and take home a feeder....


The middle tire on the feeder is chewed up, so you will need to replace that first.

You would drill holes in the table of the machine you want to use the feeder on and then bolt the feeder's base to the table. Feeders aren't typically used on jointers but they are absolutely indispensable for a shaper and can be handy for ripping on a 3+ hp cabinet saw or ripping/resawing on a larger bandsaw.

[Phillip Gregory]

If you are remotely close to southwest MO, I'd take you up on that one, feeders aren't cheap.

[Thomas Hutson]

i ended up passing on the jointer. It ended up being too far to drive with too many questions and the guy was not budging on price. i think the thing that got me was that he didn't tell me these things until after i agreed to purchase it. i ended up buying a planer instead which was on my short list of things. i found an immaculate bridgewood 15" planer with all the manuals and jigs for knife setting for $700. It makes beautiful cuts. ill probably try and find a helical head for it eventually but right now it functions flawlessly.