Question -- Cabinet with Sliding Door

[George Bokros]

I am making a display cabinet with a sliding door on the front. The cabinet is approx 36" wide and the door will have 1/4" beveled glass. The original design the cabinet was to be approx 32" wide so I purchased 28" drawer slides like what Woodsmith used in a project they had in the mag several years ago. Their cabinet was 32" wide.

My question is will the 28" slide I already have be adequate, I know the door will not open completely, or should I purchase new 32" slides. I found them on HD website but they are $115 for the pair. I have a lot work into the already and am planning on the glass cost to be ~$500 for the door, sides panels, top and shelves.

Use the 28: slides or buy new longer ones???

Thanks

[Brian Holcombe]

Why do you need slides, wood on wood with wax works awesomely.

[Jamie Buxton]

I'm not following you. I've never heard of drawer slides being used for a sliding door.

...maybe... You have one door that's almost the full width of the cabinet case. The door slides sideways such that it is hanging out in space to one side of the cabinet when it is open. The drawer slides support it top and bottom. Is that right?

What's the downside to having that door not open the full width of the cabinet? Do you need to put things in the cabinet that won't fit past the door? If you're just putting smaller stuff in the cabinet, I'd go with the slides you already have.

Or why not lose the sliding door concept, and use hinges. That's how most cabinet doors are mounted. And a pair of hinges will cost you less than $20.

[George Bokros]

I'm not following you. I've never heard of drawer slides being used for a sliding door.

...maybe... You have one door that's almost the full width of the cabinet case. The door slides sideways such that it is hanging out in space to one side of the cabinet when it is open. The drawer slides support it top and bottom. Is that right?

What's the downside to having that door not open the full width of the cabinet? Do you need to put things in the cabinet that won't fit past the door? If you're just putting smaller stuff in the cabinet, I'd go with the slides you already have.

Or why not lose the sliding door concept, and use hinges. That's how most cabinet doors are mounted. And a pair of hinges will cost you less than $20.

This project is based on on that was in Woodsmith a few years ago and on cabinet I found on line on a site that sells Amish made furniture.

Yes the door slides allow the door to move to the side and supports the door when open.

I have no downside to the door not completely sliding completely open.

The reason for the sliding door is to not have any stiles in the middle of the front of the cabinet interrupting the view of what is in the cabinet.

[Brian Holcombe]

Ah, I understand what you are doing now. That is very interesting. I usually make sliding door cabinets in a way that I have two tracks in the cabinet and two doors, slide it over infront of the opposing door to access.

[George Bokros]

Here is a picture of a cabinet with a sliding front door. I am making a different base.


357851

[Jamie Buxton]

Here is a picture of a cabinet with a sliding front door. I am making a different base.


357851

Yeah, use hinges. Way less expensive. No ugly drawer slides to look at when the door is open.

[larry senen]

i believe there are slides used in kitchen islands that slide from both sides of the island. something to consider?

[George Bokros]

i believe there are slides used in kitchen islands that slide from both sides of the island. something to consider?

Sliding from both sides don't I end up with a stile in center? I really do not like that.

Could use two shorter drawer slides to make it slide both sides.

[George Bokros]

Yeah, use hinges. Way less expensive. No ugly drawer slides to look at when the door is open.

There is no reason to have it open when people are viewing it.

[Sam Murdoch]

I like the design quite a bit, though I think the drawer slides add some bulk, the operation is a pretty cool idea.

Here are a few sources for less than you found - https://www.woodworkerexpress.com/Side-Mount-100-500-lb.-Ball-Bearing-Slides-Side-Mount-100-lb.-Ball-Bearing-Slides-32-Zinc-Plated.html?utm_source=google&utm_medium=cse&utm_campaign=google_product_ads&source=googlebase&gclid=CjwKEAjw8ZzHBRCUwrrV59XinXUSJADSTE5k-uTr9DfW_hE47FkhHsmTGBDGHXG6kl2FaMsLAnro8xoCvHnw_wc B


http://ahturf.com/store/index.php?route=product/product&product_id=93453&gclid=CjwKEAjw8ZzHBRCUwrrV59XinXUSJADSTE5kUS_p9MaF XMwfh-1X0bO5SQ1SMn22TCwZj_huytAOURoCGQfw_wcB

And here is a different design that has a taller profile is only 30" long BUT with 1" Overtavel - that gets you close to the needed 32" - https://www.woodworkerexpress.com/Knape-and-Vogt-KV-8505P-30-Side-Mount-150-lb.-Ball-Bearing-Sildes.html?utm_source=google&utm_medium=cse&utm_campaign=google_product_ads&source=googlebase&gclid=CjwKEAjw8ZzHBRCUwrrV59XinXUSJADSTE5kYxOeFbGo vJ6nA9pDYPFlobzV4GDmvqNzNgkud9NRXBoC6pPw_wcB


OH - and did I say that I would NOT compromise this project with the shorter slide to save money. You are already making a big investment. I vote - do it right.

[John TenEyck]

$500 for the glass? That seems really high, even for tempered glass. You might want to contact these two companies for a quote:

http://www.paragontemperedglass.com/

(http://www.wolverineglass.com/) http://www.wolverineglass.com/

No affiliation, just a satisfied customer.

John