New G0766 issues

[James Williams 007]

This lathe is a behemoth. It arrived in perfect condition the crate didn't have a scratch on it and everything was packed impeccably. I managed to get it set up within an hour with ease. It has a lot of metal and everything feels solid. I have no doubt it's going to be a great lathe if I could get it started. After I got the power run to it I went to turn it on and I could hear the inverter come on in the back but then it shut off after the RPM display blinked all zeros. I did a basic check to make sure there were no loose wires or anything that I could see that was immediately wrong. If I press the green power button in it keeps doing the same thing. Does anyone have any suggestions or has anyone faced this problem before? I'm sure Grizzly will be able to resolve the problem on Monday but I'm dying to get this thing running.

[Ken Fitzgerald]

Have you tried unplugging it or if it's direct wired, turning the breaker off? In either case, leave it off for at least 60 seconds and then reenergize it. My PM3520B inverter has power applied all the time unless I unplug it or flip off the wall breaker for it.

[James Williams 007]

Yeah I tried that and I tried checking the breaker I even tested another machine on that outlet to ensure everything was running fine.

[Roger Chandler]

The G0766 has a safety feature built in. You need to have the foward/reverse switch set to neutral... the straight up vertical setting. Then hit the green button, turn the foward/reverse switch to foward, then turn up the speed dial. That requirement prevents you having a large unbalanced piece mounted, and turning the lathe on while the speed dial is turned up high, which could cause severe injury or death should it fly off the lathe.

It is an extra safety step built in. When I first unpacked my lathe and set it up I thought something was wrong, but figured it out. The G0766 is a fine machine!

[James Williams 007]

I just got off the phone with tech support and they are unsure of how to fix the problem but they are sending me a new on/off switch to see if that gets it running. But the tech didn't seem real confident and wasn't completely familiar with the machine. As always they were nice and I am sure they will make it right eventually.

[Brice Rogers]

I am skeptical that the problem is the on-off switch. You may want to do some trouble shooting to speed up the entire repair process. The on-off emergency switch has a relay inside of it. With power applied, when you press in the green button, it stays in the on position. If you are not plugged in, you'll notice that the green button goes in and out with finger pressure but doesn't stay in the on position. Because you described the rpm indicator stays on (but the motor doesn't run) suggests that the on-off switch is supplying power to something.

If you are comfortable taking voltage measurements with the power on, you may want to probe the 220 volt wall plug and then on-off switch. It switches (as you would expect) both hot sides of the line.

Familiarize yourself with the electrical diagram in the manual (perhaps page 42). The power goes to the on-off switch with a white and a black wire. The voltage from the white to the black wire at the bottom of the switch should be the line voltage (around 230 or 240 volts AC) when the switch is pushed in. Then probe the voltage from white to black at the top of the switch. It should be the same.

If you pull the cover off of the power inverter box, you should be able to locate the black and white (and green) wires supplying the power. It would be good to check these also. Perhaps a wire got loose in transit.

[Brice Rogers]

BTW, if you pull the cover off of the invertor, you should be able to read the error code. That may go a long way to correctly diagnosing the problem.

[Roger Chandler]

From your pic on the GGMG, it looks like you have the wrong wall receptacle. You need a 240V Nema 6-15 or Nema 6-20 receptacle, and your wiring needs to be both black and white wires hot, and bare copper to ground.

[James Williams 007]

On the inverter it displays "Lu" when I hit the on button.

[James Williams 007]

The outlet in the picture is a regular outlet the true outlet is in the corner that can't be seen and it is a 6-15 on a 20amp breaker.

[James Williams 007]

When I push in the green power button should it click and stay in? My green power button will not stay in and it doesn't click.

[Roger Chandler]

Does sound like a faulty switch...my green button does click and stay in until the red switch is pressed.

[Brice Rogers]

I believe that the Lu error code stands for "low voltage".

When you press in the green power on button it should stick in. The relay in the switch causes it to latch. If you hit the emergency button it breaks the circuit and the relay drops out.

If the green button pops out, then it is (probably) either a bad switch or you don't have 230 vac to your machine.

Have you used a voltmeter at the receptacle?

[James Williams 007]

OK so I owe an apology to you all and especially Grizzly. I feel like a complete moron! The lathe wouldn't start or run because I didn't supply the proper power. In my haste to run an outlet for the lathe I failed to connect both poles. Along with wiring an outlet for the lathe I also put in new LED's for the shop and other outlets for hand tools and when I was at the box I wired the lathe like the other circuits and connected one pole and the the other wires to the neutral and ground bus. I figured it out last night and couldn't believe it! I connected the other pole and its running perfectly. Wow this thing is amazing! I have only turned on my midi lathe with a 10" swing and no variable speed so this lathe feels like I went from a Kia to a Ferrari! I turned some new handles for the banjo and the tailstock out of curly maple so I could acclimate to the variable speed and get comfortable with the controls. I filed down the spindle shoulder so my chuck would go on as well.

[Brice Rogers]

Thanks for the feedback, James. Enjoy your new lathe. Post some pictures of your finished work.

[Roger Chandler]

OK so I owe an apology to you all and especially Grizzly. I feel like a complete moron! The lathe wouldn't start or run because I didn't supply the proper power. In my haste to run an outlet for the lathe I failed to connect both poles. Along with wiring an outlet for the lathe I also put in new LED's for the shop and other outlets for hand tools and when I was at the box I wired the lathe like the other circuits and connected one pole and the the other wires to the neutral and ground bus. I figured it out last night and couldn't believe it! I connected the other pole and its running perfectly. Wow this thing is amazing! I have only turned on my midi lathe with a 10" swing and no variable speed so this lathe feels like I went from a Kia to a Ferrari! I turned some new handles for the banjo and the tailstock out of curly maple so I could acclimate to the variable speed and get comfortable with the controls. I filed down the spindle shoulder so my chuck would go on as well.Glad you got it up and running! I had a feeling it was something other than the lathe. We hope you enjoy yours as much as we have enjoyed ours! I particularly like your Farrari analogy....I don't now if I would go quite that far, but the 0766 is a pretty sweet ride for sure! :D

[daryl moses]

Glad you finally got I figured out and your up and running.
I couldn't help but notice from the pic of your lathe that the motor is almost up against the wall, probably not a big deal but you really need to give it some "breathing" room.
Enjoy your new lathe!!

[David M Peters]

Way In order that you feel like less of a moron I'll tell you my table saw story. I spent a day unable to turn on my new table saw because its stop button (on the mag switch) didn't have arrows telling you to rotate-to-release, and it shipped with the button pushed in.

[David Herring]

We've all had brain outgassing at some point or another. Seems like the older I get, the more my brain likes to pass gas a little more often.:D

[Dale Miner]

OK so I owe an apology to you all and especially Grizzly. I feel like a complete moron! The lathe wouldn't start or run because I didn't supply the proper power. In my haste to run an outlet for the lathe I failed to connect both poles. Along with wiring an outlet for the lathe I also put in new LED's for the shop and other outlets for hand tools and when I was at the box I wired the lathe like the other circuits and connected one pole and the the other wires to the neutral and ground bus. I figured it out last night and couldn't believe it! I connected the other pole and its running perfectly. Wow this thing is amazing! I have only turned on my midi lathe with a 10" swing and no variable speed so this lathe feels like I went from a Kia to a Ferrari! I turned some new handles for the banjo and the tailstock out of curly maple so I could acclimate to the variable speed and get comfortable with the controls. I filed down the spindle shoulder so my chuck would go on as well.

Cheap lesson.

Much better to have wired the 220 outlet 110, than the 110 outlets and lights 220. Of course you would have found the problem sooner the other way, but not at such a low cost.

[Mark Greenbaum]

Now that you have it up and running, ENJOY!! I have been so lucky and have enjoyed mine immensely. But remember - keep the break turned off or unplug from the outlet when not in use. A spike from a lightning storm or power supplier could wreak havoc on the VFD, and it's not cheap to replace. Have fun, and good luck.

[Ted Baxter]

Dave where in Okla are you? I am in Tulsa

[David Herring]

Dave where in Okla are you? I am in Tulsa

Heyas Ted, I'm in Davis.

[Leonard Niemi]

If I remember correctly it should be hooked up to a 15 amp 220 breaker not 20 amp 220.

[david privett]

the gauge of the wire you ran dictates the plug to use if you ran 12 use the 20 amp if you ran 14 use the 15 amp. Most 20 amp receptacles takes 15 and 20 amp plugs. if by chance you ran 10 ga. wire go with the 20 amp breaker and plug. Of course the breakers should match wire size for your amp draw.

[James Williams 007]

I did 10 gauge wire and went with 20 amp breaker.