Which bench top planer?

[Rick Cicciarelli]

I haven't looked into these in a while because I was leaning more towards a larger floor model. Since that may be several years out though I was thinking of just breaking down a picking up a more affordable bench top planer. I know the dewalt 735 has good reviews but at $650 it seems like it is inching its way towards a Grizzly floor model. Are there any other benchtop models to consider or will they all be a bit crummy compared with the 735? I guess I'm looking at the Dewalt 734, Rigid, Delta or other possible options under $500, unless there is a particularly strong argument for just going with the 735 at $650.

[Scott Brader]

I have a 735 and it suits me just fine. I bought it when they threw in the mobile stand. That's necessary in my shop because I am constantly moving things around my small space. I haven't had any problem with the 735. I typically only use cherry, soft maple and pine, so I'm not really stressing it very much.

[michael langman]

I picked up a dw734 used for 250or 275 dollars. Is more then adequate for my uses and works well. Some of the other later lunch box planers are not as reliable then this one as the reviews have said.

[Robin Frierson]

I started out with the 734 before the 735 came along and it worked fine. The thing I like about the 735 is you can put a helical head in it and that is a joy to use. Otherwise you will have tearout to deal with.

[Ted Diehl]

After much research I decided on the Cutech 40200H-ct over the Dewalt 735. The reviews and customer satisfaction on the DeWalt were very good but I decided on the Cutech because of the "spiral" cutter as opposed to straight knives that are used on the Dewalt. With the Cutech, if one of the cutters get a chunk taken out of it or dulls over time, you merely loosen up the individual cutter head and rotate it 90 degrees to use a fresh edge; with the Dewalt you have to replace the knives. I used it recently to plane down some Poplar and it did an outstanding job. I paid $579 plus shipping for it.

[Mike Henderson]

I have the DeWalt 735 and have been very satisfied.

Mike

[lowell holmes]

I have the Dewalt 734 and I am completely happy with it. I bought it instead of a 735. I don't regret it. It has never failed to do what I needed.

[John Lankers]

Nothing wrong with the DW735, however if noise is a concern get a floor standing planer.

[brian zawatsky]

I had a 735 and liked it, with one exception. The HSS knives are TERRIBLE! As far as I know, there are no aftermarket knives that fit it, so you have to buy DeWalt's crappy steel. Run some hard maple and you have chipped and dull knives after 50 feet worth of passes.

Someone mentioned upgrading a 735 to a spiral head. At that point, you may as well just buy a Grizzly floor standing unit. I bought a G 0543Z several months ago, and am happy with it.

Alternatively, look for a deal on a used Delta DC-380. If you're patient they can be had for 7 or 8 hundred bucks. Totally worth the extra scratch compared to a cheaper lunchbox planer.

[Ben Rivel]

DeWalt 735 is by far the most loved. Especially if you upgrade it with a helical cutter!

[Larry Frank]

That is an interesting choice on the Cutech. I hope you will have a thorough review in the future.

[Mike Kees]

I have never owned or used the dewalt 735. However I do own a dewalt 734. It is a superb little planer, I use it for jobsite finish work. I would also second the opinion to look for a used DELTA DC 38O . i think that in the long run you will be happier with a full size planer,so I would not pay for a helical upgrade in a portable planer. That is just how I see it,many others really like a dewalt 735 with helical head.

[John Lankers]

I had a 735 and liked it, with one exception. The HSS knives are TERRIBLE! As far as I know, there are no aftermarket knives that fit it, so you have to buy DeWalt's crappy steel. Run some hard maple and you have chipped and dull knives after 50 feet worth of passes.


Brian, here is one source for aftermarket knives: http://dimar-canada.com/products.php?m=56&idp=16

[Jay Aubuchon]

As far as I know, there are no aftermarket knives that fit it, so you have to buy DeWalt's crappy steel.

Infinity offers replacement knives:

HSS Knives For DeWalt 735 Planer (http://www.infinitytools.com/jointing-planing/jointer-planer-knives/dewalt-dw734-and-dw735-planer-knives-2765)

and

Carbide Tipped Knives For DeWalt 735 Planer (http://www.infinitytools.com/jointing-planing/jointer-planer-knives/dewalt-dw734-and-dw735-planer-knives)

[Russ Kupiec]

My two cents.......Seems I would be the outlier here. I have the newer Makita(2012nb) with the cutting head that moves up and down, it's a replacement for the older Makita where the cutterhead was fixed and the table moved up and down. I purchased both because they are truly portable(nice in a small shop) maybe 25-30lbs lighter than the big Dewalts. If portability is a factor I'd recommend the Makita. Blade changes are quick and easy. Dust collection requires buying an overpriced exit hood but as long as it's hooked up to a collector it works well. If I'm doing alot of planing, I'll take the planer outside and remove the hood. All the shavings land nicely in a pile for easy clean up. The finish is very good, although as with any tricky grain, switching to a set of sharp blades(I keep an extra set for this use) is a necessity as would on any other planer. Blade life is excellent and they are two sided blades. With sharp blades mounted I get about the same surface I get off my helical head jointer, also with fresh cutters. Birds eye maple is the most challenging for either tool and I still have to hand plane the final surface for zero chip out.

[Rick Cicciarelli]

Anyone else had experience with the Cutech? That looks like an interesting one at that price point. The few reviews I've read seem to be pretty positive.

[Jack Lemley]

Brian,

Infinity actually sells aftermarket steel and carbide blades for the DW735. I have the DW735 and upgraded it to the Shelix head a couple of years ago and never looked back. Great combo!

Jack


I had a 735 and liked it, with one exception. The HSS knives are TERRIBLE! As far as I know, there are no aftermarket knives that fit it, so you have to buy DeWalt's crappy steel. Run some hard maple and you have chipped and dull knives after 50 feet worth of passes.

Someone mentioned upgrading a 735 to a spiral head. At that point, you may as well just buy a Grizzly floor standing unit. I bought a G 0543Z several months ago, and am happy with it.

Alternatively, look for a deal on a used Delta DC-380. If you're patient they can be had for 7 or 8 hundred bucks. Totally worth the extra scratch compared to a cheaper lunchbox planer.

[Bill White]

Don't have the Cutech planer, but the benchtop jointer that I have is quite a bargain. The replaceable cutters really make it easy to use, and do a fine job.
I would hope that the quality will translate to the planer. My old 733 DeWalt is still goin' strong.
Bill

[Michael Zerance]

I've had the 735 for about 10 years and it's been great.

It is loud.

It's currently $550 at CPO or $520 if you'll take a recon; free shipping.

[Art Mann]

Anyone else had experience with the Cutech? That looks like an interesting one at that price point. The few reviews I've read seem to be pretty positive.

Yes! That is exactly the same machine which used to be sold in Home Depot stores under the Ridgid brand as the model TP1300 (IIRC). It is a fine planer that I just replaced after 10 years of constant use. The only reason I sold it is that I bought a new Jet jointer/planer combo machine. It is faster and much quieter than the TP1300 but the surface finish and thickness consistency is not one bit better.

[Jim Dwight]

I have an old Ryobi AP-10 I bought from a guy at church for $100. It hardly worked when I got it but it was just dull knives. I bought another set but tried sharpening the originals and they now work great. The replacements haven't been used. It is only 10 inches wide but that is rarely an issue. I have it on a flip top stand with my Jet hollow chisel mortiser. I use the planner a lot more than the mortiser. I'm sure the newer ones have advantages but my little Ryobi is good enough, at least for now.