Seen at the fest today

[steven c newman]

A few wood working items...
343564
They were trying to hand crank this to start it up...
343565
Why are they just sitting around? IF you look closely, you will see the BIG saw blade leaning against that wagon back there. The Farmall tractor's PTO will power the wide belt..
343566
Whenever they fix the bearings. And, that is the small blade, to boot.
343567
Vise was a bit more than I had in my pocket....$24...had other things to see..
343568
The BIG plane is a KK 8c, they only wanted $110 for it, beside it is a #6c @ $45.
343570
Yep, it says KK 8...the #80 was $25....That roll of auger bits in the last picture? $40. I did buy a few things....spent a whopping $10 today, and had $6 left in my pocket...Hammers, anyone?
343571
LONG..HOT...tiring day, walked over 2 miles again. that was after about the same yesterday....I think I will pass on going down there tomorrow...now, IF this thing had been full..
343572
The Oak one, of course. Just my luck, dry town, empty barrel...somehow, it figures...:(

[Gary Cunningham]

Swappers Day. Spent about four hours looking for nice rusty stuff. All I saw was crusty/beat up and generally not worth bringing home.

I did spend less (on tools) than you. I paid a buck for a brass brush.

[Richard Line]

Imagine the size of dovetails that first saw (mill) would cut. :D

[steven c newman]

Dollar for the handle, dollar for the chisel......
343575
Buck Brothers 3/8" Mortise chisel

343576
Couple of $1 Millers Falls 3/4" chisels, the $1 block plane iron has a triangle Stanley logo. The offset screwdriver is a Stanley No.3400 ( $0.25) the bit and countersink were a quarter each. Not too sure about that $2 tri square, but it does have a level in the handle ( oooh, aaahh) Nail set is a 3/32" VA USA. Not a great day, but is was cheap. Worst part was getting back into a BLACK van that had sat out in the bright sun all afternoon....

I doubt IF I will go back there tomorrow, fest runs until Monday evening...I'm just plumb worn out.

[Glen Canaday]

It would have been hard to say no to all them chisels for a buck each.

[steven c newman]

A few more looks
?343579
They wouldn't let me ride this around, so I had to walk...
343580
Same here.
343581
Water pump, belt powered?
343582
Hmm, too bad I didn't need a hatchet, or a hammer. He had three Broadaxes in another of these tubs....but they were without a handle.
343583
But, this is why it was called a Tractor Fest....
343584
From the Green & Yellows, to the
343585
Reds and white...
343586
And any other paint colour around. In the two days I spent down there, I walked over 4 miles. Had to go back the second day, just to see what I missed the first day.
Happens every Labor Day Weekend. West Liberty, OH. Lions Park. Saw Mill building is new. Admission and parking is always free. DRY Town, though...no booze is sold.

[steven c newman]

I did get that Brace cleaned up..
343588
Made by Millers Falls, sold by Keen Kutter, 6" sweep
343591
If it weren't for the Keen Kutter logo stamped by the chuck..
343594
This would have been a M-F No. 1054. @ $25........
343595
The other brace is a 14" sweep, with a holdall chuck....

[Stew Denton]

Steven,

Very nice job on the brace!

If you have already answered this same question on other tools, my apology, but I am always wondering how different folks do this same job. It seems like I am always working on rust bargains that in many cases I have owned for years, and it always seems like it takes me a lot of time to clean up old metal tools. The question is, what processes and methods do you use to clean up such as the brace? Have you found relatively quick ways to do such?

Stew

[steven c newman]

Took me maybe 10 minutes using a wire (brass) wheel. I have one for the grinder, and a few for the Drill press. IF there is a small spot they can't get to, there is a flex shaft Dremel at the ready. Doesn't take all that long to do.

[Joe A Faulkner]

My step father operated a similar sawmill on his hobby farm in southern Indiana. He ran the saw off an Oliver 88 row tractor. Working the mill in the middle of July with the infamous Ohio Valley humidity was one of the most demanding jobs I've ever had. Comes close to putting up the July cutting of hay. Talk about scary sharp, those saws bring a whole new meaning to the phrase.

[steven c newman]

Dad used to work on Archie Foster's old Ford tractor.....I THINK it was an 8N? Had to push down on the gear shift to start the blasted thing. He'd get it fixed back up, and needed a"driver" to take it back to Archie's place.....14 yr old ME.

I would much rather see these old machines restored, than sitting in some field along the road...
343627
Every now and then, the Old Coot will drag one of them back to the barn, rehab it back up, and then just sell it. Might take him a LONG time to do all of these.....and he won't sell parts, he won't sell them as is. They just sit out there and rust...Grrrrrrr!