Bowl steady rest

[Rick Bailey]

I’m looking at the Oneway but my lathe has a gap bed.
I don’t think it will work when doing shallow bowls, I can’t get the tool rest close enough with it on.
Anyone run in to this?
If so, how did you make it work?
Thanks as always.
Rick

[robert baccus]

I've been using a oneway for years. It is so adjustable that I'm sure it could be used as an offset stabilizer. The wheels do not require a 90 deg. set to work. I do crazy things with odd shaped vases frequently.

[Rick Bailey]

Thanks Robert,
The problem is I have to set the banjo so close to the gap no room for the steady to bolt down.
I do like that oneway though.

[Faust M. Ruggiero]

Rick, When I use my Oneway Steady rest for a bowl, it is usually fairly close to the banjo. If I am making a deeper vessel there is plenty of space between. It just depends on the project.

[Rick Bailey]

Rick, When I use my Oneway Steady rest for a bowl, it is usually fairly close to the banjo. If I am making a deeper vessel there is plenty of space between. It just depends on the project.

Deep bowls are not the problem, it's shallow bowls.

[Wally Dickerman]

Deep bowls are not the problem, it's shallow bowls.

My question is....why do you need a steady for a shallow bowl?

[Barry McFadden]

Rick...I'm not really sure what lathe you have but I have been wanting the Oneway bowl steady for ages but since it seemed to be for a flat bed lathe I never thought it would work for me. My lathe has 2 chrome steel bars for the bed. Recently I discovered I had an extra clamp assembly for my tool rest because the lathe came with a long tool rest with 2 posts. Forgot about the extra one because I never use the long tool rest. Went and bought the bowl steady and the extra tool rest clamp works perfectly to hold it in place...wish I'd done it a long time ago...

[Rick Bailey]

My question is....why do you need a steady for a shallow bowl?

Hi Wally,
As the rim gets thinner I get vibration and chatter.

[Rick Bailey]

Rick...I'm not really sure what lathe you have but I have been wanting the Oneway bowl steady for ages but since it seemed to be for a flat bed lathe I never thought it would work for me. My lathe has 2 chrome steel bars for the bed. Recently I discovered I had an extra clamp assembly for my tool rest because the lathe came with a long tool rest with 2 posts. Forgot about the extra one because I never use the long tool rest. Went and bought the bowl steady and the extra tool rest clamp works perfectly to hold it in place...wish I'd done it a long time ago...

That looks like set Barry,
I try to post some pics and see if that helps explain what I'm try to say.:o

[Rick Bailey]

Lets see if this helps.



314856314857314858

[Robert Henrickson]

I’m looking at the Oneway but my lathe has a gap bed.
I don’t think it will work when doing shallow bowls, I can’t get the tool rest close enough with it on.
Anyone run in to this?
If so, how did you make it work?

As the rim gets thinner I get vibration and chatter.

There is no need for a steady. To take an extreme case, I have turned numerous thin plates (1/8" to 3/16" maximum thickness) , 12-16" in diameter from 1" thickness disks. I rarely use thicker stock. Just as with hollowing a deeper bowl, you have to work inward from the rim to final thickness in stages, not all the way from rim to center all at once. By the time you are perhaps a third of the radius toward the center, you should not return to the rim. Some vibration may develop, and the rim itself may deviate slightly from true as stresses release in the wood, but the ever diminishing central area you are working should behave.

[Rick Bailey]

There is no need for a steady. To take an extreme case, I have turned numerous thin plates (1/8" to 3/16" maximum thickness) , 12-16" in diameter from 1" thickness disks. I rarely use thicker stock. Just as with hollowing a deeper bowl, you have to work inward from the rim to final thickness in stages, not all the way from rim to center all at once. By the time you are perhaps a third of the radius toward the center, you should not return to the rim. Some vibration may develop, and the rim itself may deviate slightly from true as stresses release in the wood, but the ever diminishing central area you are working should behave.

That is very good advice, I never thought of that.
And sorry I forgot to mention I'm still new at this.:rolleyes:
Thanks Robert.

[robert baccus]

The above is good advice. But now that you are in a fix you might try this. A #2 taper shaft extension would fix this easily. You may be able to turn your wheels 90 deg. and ride them on the plate face and get by?? ( Craft supplies at $16.75 )

[Jeffrey J Smith]

You could also look at look at a dogleg offset for your banjo. It will allow you to move the banjo about 3" towards the tailstock. Might allow enough room to mount the Bowl Steady. Robust offers one with a 1" toolpost.
But, I've got to agree that if you turn in stages from the rim down - I usually complete the outside shaping and finish as you go down the inside. If a little vibration happens, generally a little gentle pressure from the left hand will dampen it easily.

[robert baccus]

The old 80grit gouge will remove wood with no vibration. I won't tell.

[Thom Sturgill]

Another option is to get a Robust J rest or curved bowl rest and move the banjo further out. Even a standard Robust rest will give you an inch or so and get you closer to the material than that large bar.

[Rick Bailey]

Another option is to get a Robust J rest or curved bowl rest and move the banjo further out. Even a standard Robust rest will give you an inch or so and get you closer to the material than that large bar.

I think that's what I'll do,
Thanks Thom.
I have a bestwoods curved rest that I hope will do the trick.
Robust won't fit my lathe, I have a 3/4 post.

[Dave Fritz]

Rick,
Not sure but I'll bet Brent at Robust would make one up for you.
Dave Fritz

[Brian Myers]

I think that's what I'll do,
Thanks Thom.
I have a bestwoods curved rest that I hope will do the trick.
Robust won't fit my lathe, I have a 3/4 post.

From the robust web site "

Please note, lathes with a 25mm diameter post such as the Grizzly or Laguna 1847 or their clones, are easily mistaken for 1” diameter posts, which will not fit.
25mm and 30mm Metric sizes are available special order, as are ¾”, 7/8” 1 1/8” and 1 ¼”.
Extra charges will be incurred for special made toolrests. Please place orders for specials over the phone. "