Lathe work area setup

[Wes Ramsey]

As I get more into turning I find that my tools and whatnots far exceed the capacity of the one shelf I currently have over my lathe. I'm thinking about repositioning it perpendicular to the wall instead of against it, but then I lose the ability to have everything right there at eye level. Could y'all offer some tips for how to organize this area of my shop and maybe post some pics? Thanks in advance!

[Lee Reep]

I'll try to take a pic tomorrow and post. I bored a several foot length of X4 oak piece I had to hold my chisels, plus various centers, chucks -- accessories I most frequently use. I used various sizes of Forstner bits to bore appropriately sized holes. In addition, I use a rolling 5-drawer Craftsman hobby cart. I use it to organize lathe accessories -- calipers, tool rests, chuck jaws, etc. The sides are punched like pegboard, so I hang a bunch of stuff from the sides. Best of all, I roll it at an angle to my lathe, so it is easy to access, but can be rolled against the wall and out of the way when I'm not using the lathe.

[charlie knighton]

when I go see demostrations, most demostrators just have a table behind them with tools, chucks, calipers, etc on it.......now wheather you need anything more elebrate than that or not is up to you, but that flat area is most helpful

[Thom Sturgill]

My Jet 1642 lathe is in the center of the shop area, I can easily walk all the way around it. The table saw is about 4' behind it.

I find that for any given project I will only use a few tools. I have a 2x10 shelf below the lathe bed mounted on abracket in the leg castings and put the tools I will use there. Always have the parting tools and whatever gouges, scrapers, and skews I expect to use. I have a table behind me with tool racks on either end and a rolling rack that has bowl gouges on one slanted side and hollowing tools on the other. Sanding disks are stuck in the pegboard on the gouge side. Largers items such as the steady rest are on shelves between the two slanted faces. The table has several drawers - the top one being divided and holding spur centers, parts for the live center, jacobs chuck, etc and the next drawer has the buffing wheels and extra tool rests. Sand paper (sheets) are in a rack on the table, extra disks in a rolling tool cart at one end of the table.

There is a post at the headstock end that brings power to the lathe and has pegs for the chucks and holds the vacuum system. A 4' power strip is mounted to the back edge of the shelf below the lathe.

I'd take pictures, but then I'd have to clean up some first. :D

[Wes Ramsey]

My Jet 1642 lathe is in the center of the shop area, I can easily walk all the way around it. The table saw is about 4' behind it.

I'd take pictures, but then I'd have to clean up some first. :D

And that's why I hadn't asked before now. Can't expect y'all to do it with the condition mine is in :eek:

[Michael Mills]

It may or may not give you some ideas but it works well for me. Located behind the lathe, since mine is 16" turning max, doors would clear the largest turning by about 3".
I went with double doors (outer doors mounted to inner doors).
Cabinet about 5' long total, 30" high, about 14" deep with both door closed. If you went with single door then about 10" deep.
Individual doors are 24X30H; outer doors 3.5" deep, inner doors 5.5" deep, shelves 5.5 deep.
By utilizing deep doors and pegboard in the center, each side would be 2.5+" deep or deep enough for almost any tool. Single doors would give you 8 linear feet of storage (mine has 16 linear feet using double doors).
Except for a few finishing items there is never a need to reach over the headstock while spinning (I pull down the finishing items first). Any item stored there would require stopping the lathe to use anyway.
Some minor items..
Pull down shade on the left (over headstock) to protect items from water or finish. Also provides a nice backdrop for watching the shadow edge on some items. Also keep chips out of the shelf area on the left.
Gooseneck spot mounted in center allow plenty of light for the interior or an item or to bring down parallel to check for sanding lines or other flaws prior to applying finish.
Some folks don't like magnetic strips but they do not bother me. You can get good pegboard spring clips for the tools down to about 1/8" which will hold nicely and last a lifetime.
Two screwdrive type holders on one of the doors hold up to 10 drive center, drill chucks, etc.
I can reach any item with one step max from the center of the lathe.
One pic outer doors open, inner doors closed (of course there is storage on the outside of the outer doors also).
One pic both doors open and cabinet interior.
Typically the right outside inner door (whew) does not have all those tools. I usually keep that door closed during turning and it holds only the chisels and tools needed for that turning, probably six at the very most. Closed also keep chips out of the shelf area on the right.

[David Delo]

Very nice set-up Michael.

[Peter Fabricius]

A couple of considerations to include in your set up.
Reaching over the Lathe when turning is generally not a good idea.
Placing your turning tools at either end of the Lathe makes sense for easy reach.
The shelf behind the Lathe can be good for Centres, Chucks and attachments that will only be reached for when the Lathe is turned OFF.
A mobile cart for the turning tools seems to be the preferred solution in a tight shop because it can be rolled back against a wall when not in use.
Just a few thoughts.
Peter F.

[Lee Reep]

Here is the picture of the tool holder I made from a 4X4 chunk of oak. Someone gave me the wood, and after a few years of not knowing what to do with it, I decided a tool holder for the lathe was a good use. Also pictured is my Craftsman rolling cart. The top has a sliding lid, so I store a number of pen blanks in the compartments. I'd probably prefer a solid top, and maybe mount my grinder on it, but it works out pretty well as-is. I have two scroll chucks and about 10 sets of jaws, and a Beall collet chuck and 6 collets, so the bottom drawer is devoted to chucks. Sanding supplies, measuring tools, pen bushings, and lots of miscellaneous stuff is stored in the cart. The pegboard-style sides have a variety of other tools hanging for easy access.

I like the idea of a storage cabinet on the wall and may have to build one at some point. The oak block is behind my lathe bed extension. Like others have mentioned, you do not want to be reaching over a spinning lathe to grab something. Worst case I reach over the tailstock. I do not do really long spindles but to turn tool handles or pepper mills, you just do not have adequate distance between centers on a typical midi lathe, by the time you add a drill chuck and drill bit into your tailstock for boring a spindle, or tool handle, pepper mill, etc.

303467303466

[David Delo]

[QUOTE=Lee Reep;2356453]Here is the picture of the tool holder I made from a 4X4 chunk of oak. Someone gave me the wood, and after a few years of not knowing what to do with it, I decided a tool holder for the lathe was a good use. Also pictured is my Craftsman rolling cart. The top has a sliding lid, so I store a number of pen blanks in the compartments. I'd probably prefer a solid top, and maybe mount my grinder on it, but it works out pretty well as-is. I have two scroll chucks and about 10 sets of jaws, and a Beall collet chuck and 6 collets, so the bottom drawer is devoted to chucks. Sanding supplies, measuring tools, pen bushings, and lots of miscellaneous stuff is stored in the cart. The pegboard-style sides have a variety of other tools hanging for easy access. I like the idea of a storage cabinet on the wall and may have to build one at some point. The oak block is behind my lathe bed extension. Like others have mentioned, you do not want to be reaching over a spinning lathe to grab something. Worst case I reach over the tailstock. I do not do really long spindles but to turn tool handles or pepper mills, you just do not have adequate distance between centers on a typical midi lathe, by the time you add a drill chuck and drill bit into your tailstock for boring a spindle, or tool handle, pepper mill, etc.Lee,How long have you been storing a lot of your lathe accessories in a tool storage cart? Do you like doing it that way or would you prefer some other method? Reason I ask is that I've recently switched from a 10-shelf bookcase type unit as one part of my lathe tool accessory storage to the red Harbor Freight 5-drawer tool cart. I liked the shelf deal because you turn around and everything is there in plain site and you just grab what you need. Easy and convenient but dust does settle and needs cleaning from time to time. Jury still out for me because I've only been using this cart/drawer system for a couple weeks. Not quite as convenient but stuff does stay cleaner and can keep things organized by category a little better.

[David Delo]

Lee,Couldn't edit last post so here goes. How long have you been storing a lot of your lathe accessories in a tool storage cart? Do you like doing it that way or would you prefer some other method? Reason I ask is that I've recently switched from a 10-shelf bookcase type unit as one part of my lathe tool accessory storage to the red Harbor Freight 5-drawer tool cart. I liked the shelf deal because you turn around and everything is there in plain site and you just grab what you need. Easy and convenient but dust does settle and needs cleaning from time to time. Jury still out for me because I've only been using this cart/drawer system for a couple weeks. Not quite as convenient but stuff does stay cleaner and can keep things organized by category a little better. Dave

[Paul Heely]

Here are some pics from my shop. I use the desk by the lathe to also hold the tailstock when I'm working off the end of the lathe. Plastic shelves hold my supply of cut wood, the rest sits outside in longer lengths until I'm ready for it. The closet behind the bandsaw and grinder houses the dust collector and compressor. Hope it gives you some ideas.


303525 303526 303527 303528

[Thom Sturgill]

Finished the project I was working on and am getting ready to go to the Florida Symposium tommorrow so I did some cleanup and tool a few pictures:
303649303650303651303652
First image is right side of workbench behind me when turning - spindle tools.
Second shows the movable cart with bowl gouges, you can see the TS extension table which folds down.
The third is the other side of the cart with hollowing tools, you can see the power strip on the shelf below the lathe bed.
The last is the workbench showing the other tool rack and drawers. Only the top drawer is that organized.:D There are anti-fatigue mats between the lathe and the workbench.

I know most people do not have as much room around their lathe. I have wire racks behind the workbench that hold blanks and a plastic shelf unit that holds finishing supplies. My micro-motor tool and wood burner are on a separate workbench where I can sit.

[Wes Ramsey]

Thanks for the tips and pics guys! Keep 'em coming!

I do have some basic ideas in mind for what I want, but I'd love to see more pics. I don't mind admitting that I'm going to shamelessly steal all the ideas I can :D I hope to get started on the new setup maybe late spring. I have room and I have lumber, but I need to sell a few pieces to pay for hardware and the shop is awful cold right now.

[Kyle Iwamoto]

Thanks for the tips and pics guys! Keep 'em coming!





Here is what I do. 5 gallon bucket with PVC pipe.
I put a cap on the end, and a coupler on the top so they even out. Tape the PVC together and fill with expanding foam.
Everything in my shop has to move, and the other benefit is when I do demos, I just pack along the bucket and have most of my tools.

[Wes Ramsey]

Finished the project I was working on and am getting ready to go to the Florida Symposium tommorrow so I did some cleanup and tool a few pictures:
303649303650303651303652
First image is right side of workbench behind me when turning - spindle tools.
Second shows the movable cart with bowl gouges, you can see the TS extension table which folds down.
The third is the other side of the cart with hollowing tools, you can see the power strip on the shelf below the lathe bed.
The last is the workbench showing the other tool rack and drawers. Only the top drawer is that organized.:D There are anti-fatigue mats between the lathe and the workbench.

I know most people do not have as much room around their lathe. I have wire racks behind the workbench that hold blanks and a plastic shelf unit that holds finishing supplies. My micro-motor tool and wood burner are on a separate workbench where I can sit.

Thom,

Is that a glass top I see on your desk? Makes good sense for finishing as you can easily scrape off drips and such. I found a large plate of glass in our attic last week left by the previous owners. Hadn't occurred to me to re-purpose it to a desk top before, but it just did. Thanks!

[John Keeton]

Wes, for whatever it may be worth to you, the following thread includes some pics, and in a post by me, a PDF file that has the plans for tool racks. Hope it gives you some ideas.

http://www.sawmillcreek.org/showthread.php?159802-Question-about-your-tool-rack

[Thom Sturgill]

Thom,

Is that a glass top I see on your desk? Makes good sense for finishing as you can easily scrape off drips and such. I found a large plate of glass in our attic last week left by the previous owners. Hadn't occurred to me to re-purpose it to a desk top before, but it just did. Thanks!

No, its a piece of tempered hardboard that I can easily replace. LOL, I think glass would shatter the first time I threw a tool onto the bench.

I do have a glass turntable (lazy susan) that I use when spraying small items off the lathe. Same idea, I take a razor to it and scape off the build up occasionally.

[Stan Smith]

I was just going to write a long description, but a pic is better, IMO. I like the magnetic bars. Mine racks are simple and rustic. I had to add to them because the EWT chisels are aluminium.

303748

[Lee Reep]

Lee,Couldn't edit last post so here goes. How long have you been storing a lot of your lathe accessories in a tool storage cart? Do you like doing it that way or would you prefer some other method? Reason I ask is that I've recently switched from a 10-shelf bookcase type unit as one part of my lathe tool accessory storage to the red Harbor Freight 5-drawer tool cart. I liked the shelf deal because you turn around and everything is there in plain site and you just grab what you need. Easy and convenient but dust does settle and needs cleaning from time to time. Jury still out for me because I've only been using this cart/drawer system for a couple weeks. Not quite as convenient but stuff does stay cleaner and can keep things organized by category a little better. Dave


Dave,

I like the cart pretty well. My problem is that with a small basement shop, something is always getting moved out of the way. My cart sits in front of the basement escape window, so I can roll it out to use it, and if I need to open the window, I can roll the cart out of the way.

My basement wall behind the lathe is blank (directly above the block of wood holding the tools. I'll eventually build a cabinet for that spot. Wall space is valuable in a shop, since you want to get things off the floor and out of the way if you can!

[James Combs]

Oops, posted in the wrong thread, went to look at the one John mention and got confused:o I guess.:D

[Rich Aldrich]

This is the lathe tool rack that I use. I also attached the PDF plan of this rack that I made using AutoCad. I have this rack on the wall beyond the tail stock so you dont reach across the lathe for tools.

[john snowdon]

Here is a takeoff of the design John mentions above. When I first started turning I built the rack as John posted. It works like a champ and hangs over my midi lathe. Trouble is, I became a bit of a tool junkie, bought a bigger lathe and only THEN found Doug Thompson and Dave at D-Way Tools and discovered what tools are supposed to be like. Once I finished all of the Christmas presents this year I looked at the shop and decided I was going to finally get everything organized, from my band saw accessories to lathe tools to clamps. I went back to the original tool rack plan, expanded the width to accommodate 20 tools and added a shelf below the rack. I did not round the top side pieces as I planned on adding smaller shelves to store sandpaper etc. Now I think I will add a 2nd shelf below the first for sandpaper, etc and add a plexi cover to keep chips from flying in. I also attached 2 magnetic bars to the lathe. The bar on the front is for oft needed parting and measuring tools, the bar on the side holds chuck keys, my release bar and a wrench to remove the chuck from the lathe.

My basement shop is fairly small (about 350 sq') and floor space is at a premium. Everything but the lathe is on wheels and is rolled away from the wall if more room is required. As I agree with Peter that reaching over a running lathe is not a good thing, I am building a small holder that lays flat on my jointer bed next to the lathe and will hold the 3 or 4 tools I am using for a project. Yes, the attached pictures show a very clean area. Sorry...I have no other area to do my finishing–plus I seem to have developed a sensitivity to saw dust–so I keep the shop pretty clean. I currently attach a hose from my 2.5hp dust collector to each machine as needed and am currently planning a shop wide system.

At any rate, this rack works well for me and may give you more ideas as you find what is right for you. Many thanks to Jeff Wright, Dan Forman and John Keaton for creating and posting the original plans. They definitely made it easy for me to get started.

Cheers,
John
303774303775303779

[David Delo]

John, If Norman Rockwell was still alive, he would have put your pictures in the Saturday Evening Post. I considered myself somewhat of a clean freak also but after seeing your set-up, I'll have to rethink. Wonderful looking shop, thanks for sharing.

[john snowdon]

Hey, David.
It's amazing what 2 really good sinus infections will make you do! Especially when your job involves plane travel. :D

[David Delo]

Little bit late to the party with this but I was in the midst of revising my lathe area when first posted. So here is my lathe set-up revision number 752,386!!!!!

Hollowing rig, multi rest mounted on door. Air compressor, dust collector/cyclone & shop vac in the room behind the door. Red HF service has chucks & related items in top shelf with tilt lid. Extra jaws and various lathe related stuff in the small drawers with coring system and vacuuming system having their place in the larger 2 bottom drawers. Measuring, dividers & such, DC remotes on peg board behind the cart. Lathe tools on homemade plywood cart made from a kitchen remodel job that got me started in this dust making endeavor. Sharpening station and then a metal mobile shelf unit that has most of the sanding stuff along with other shop hand tools.
304132304135304136

[Peter Fabricius]

John S,
Nice layout and many beautiful toys, eh! TOOLS,
If you turned the tailstock end of the Nova closer to the wall by the tool rack you could reach them without reaching over the Lathe. Lots of turners have the lathe angled relative to the wall.
Just a thought.
Peter F.

[john snowdon]

Thanks, Peter! I've been thinking about turning the lathe 90 degrees so it sits perpendicular to the wall so I could access the tool rack easier and also have better dust collection behind it but I was thinking of putting the head stock toward the wall so I could get better access from the end of the lathe when turning. I'll also try your idea to angle it and see if I like one of them better. Thanks for the suggestion!

Stay warm up there! Going to -7 here again tonight...

John

[Marc Tuunanen]

Outstanding rack Me thinks. Thanks to all for the pics and drawings. Think I'll bulid a couple myself.

Cheers,
Marc

[Adam Petersen]

Here is my holder. A mix of things I had in the garage. Workmate atop a HF DC rolling base with a rack of 2" PVC pipe sections. I love that I can roll it around as needed.

[Adam Petersen]

Crud. Why did it invert the pic?

[Jim Seyfried]

Red HF service has chucks & related items in top shelf with tilt lid. Extra jaws and various lathe related stuff in the small drawers with coring system and vacuuming system having their place in the larger 2 bottom drawers.
304132

I bought one of those on sale a few weeks ago to store lathe stuff in. I used some re-mount type spray glue to hold some drawer liner to the top. Then I removed the bars that lock the drawers when the top is closed. For me it is a lot more convenient to be able to open the drawers with the top closed.

[David Delo]

I bought one of those on sale a few weeks ago to store lathe stuff in. I used some re-mount type spray glue to hold some drawer liner to the top. Then I removed the bars that lock the drawers when the top is closed. For me it is a lot more convenient to be able to open the drawers with the top closed.+1 on the liner for the top surface. Haven't done it yet but plan to. Don't know what you mean about taking the bars out. My drawers open & close fine when the lid is open or closed.

[Jim Seyfried]

+1 on the liner for the top surface. Haven't done it yet but plan to. Don't know what you mean about taking the bars out. My drawers open & close fine when the lid is open or closed.

Evidently they make them differently. Mine looks just like yours with five drawers. But mine had spring-loaded bars that locked the drawers with the lid closed. I set the bracket and plastic bar cover in the location they were in the picture below.
305382

[David Delo]

Evidently they make them differently. Mine looks just like yours with five drawers. But mine had spring-loaded bars that locked the drawers with the lid closed. I set the bracket and plastic bar cover in the location they were in the picture below.305382Yeah mine is the same config as yours with the spring loaded bars but they don't lock anything when the lid is closed. Maybe mine is defective but that's okay with me.