View Full Version : 1 1/4''x8 nut
joe zarnitz
06-13-2005, 4:46 PM
looking for source---tks,joe
Jim Ketron
06-13-2005, 6:49 PM
sent you A PM Joe
Robert Grady
06-13-2005, 7:02 PM
www.fastenal.com (http://www.fastenal.com)
I use them quite a bit in the construction industry and they are nationwide.
joe zarnitz
06-13-2005, 7:24 PM
thanks for the info jim & robert ---joe
Bruce Smith
06-13-2005, 7:44 PM
Joe, thats a good question as standard 1 1/4 " USS has 7 TPI and 1 1/4" SAE has 12 TPI. I would think you will probably have to get a machine shop to fabricate one. Someone said that they were used in the construction indudtry, I would be very much interested in which manufacturer is using 8 TPI. Trust I have helped out, good luck.
Bruce in Saint John N.B.
Clem Wixted
06-13-2005, 9:02 PM
Could you share any source that you could find?
I checked a few links and couldn't find a 1 1/4 X 8 nut :-(
Clem
joe zarnitz
06-13-2005, 9:24 PM
clem sent you a pm--joe
Jim Ketron
06-13-2005, 10:42 PM
Mcmaster-Carr has them thats what I sent Joe
I orderd some a few months back they come in packs of 5
Mike Ramsey
06-14-2005, 11:21 AM
Joe, thats a good question as standard 1 1/4 " USS has 7 TPI and 1 1/4" SAE has 12 TPI. I would think you will probably have to get a machine shop to fabricate one. Someone said that they were used in the construction indudtry, I would be very much interested in which manufacturer is using 8 TPI. Trust I have helped out, good luck.
Bruce in Saint John N.B.
Bruce,
A lot of wood lathes use 8 tpi on the headstock spindles, very common it seems.
Randy Meijer
06-14-2005, 4:19 PM
I found a 1"x8tpi hex nut for my JET mini at a place called "TRACTOR SUPPLY".....sort of a farm store. They sell their big nuts and bolts by the pound. I think the nut cost me about 40 cents!!
Bruce Smith
06-14-2005, 10:38 PM
[QUOTE=Randy Meijer]I found a 1"x8tpi hex nut for my JET mini at a place called "TRACTOR SUPPLY".....sort of a farm store. They sell their big nuts and bolts by the pound. I think the nut cost me about 40 cents!!
Mike and Randy I think you misunderstood me or perhaps Joes requirements. His headstock is 1 1/4" in diameter and 8 tpi and that is not a standard size. Like I said in the answer to Joes original question, standard USS thread pitch for 1 1/4 " nut is 7tpi & SAE 1 1/4" nut thread pitch is 12tpi. Yes Mike, many lathes use 8tpi head stocks 1' , 1 1/8", 1 1/4" & 1 1/2" shafts. Of all these only the 1" 8tpi is a standard USS size and that is why Randy was able to get one at a tractor supply store. Trust I haven't totally confused you or others, just trying to be helpful.
Bruce in Saint John, N.B.
Robert Grady
06-15-2005, 7:04 PM
There are three "standard" thread series in the Unified screw thread system.
UNC- course
UNF- fine
8-UN- 8 thread series.
8-UN is available in sizes form 1" to 1-1/2"
reference the following document pages 12 and 35
http://www.fastenal.com/content/documents/FastenalTechnicalReferenceGuide.pdf
Clem Wixted
06-15-2005, 7:32 PM
Robert,
That is the first time I've seen the spec in writing for this type of nut to fit lathe spindles.
Now I know the rest of the story,
Thanks,
Clem
There are three "standard" thread series in the Unified screw thread system.
UNC- course
UNF- fine
8-UN- 8 thread series.
8-UN is available in sizes form 1" to 1-1/2"
reference the following document pages 12 and 35
http://www.fastenal.com/content/documents/FastenalTechnicalReferenceGuide.pdf
Robert Grady
06-15-2005, 7:40 PM
Your welcome Clem, Bruce is correct in the fact that a Tractor Supply or HD does not carry them as "standard". You will have to go to a Fastenal or a speacialty fastener supplier to get them, but they are a standard thread size.:)
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.