Some shop improvements

[Matt Meiser]

After 2 kitchens, 5 baths, and 2 laundry rooms I decided I've practiced enough to tackle some cabinetry for my shop. :rolleyes: Been busy the last couple weeks. I've accumulated a ton of plywood and and used a lot of that up on these projects. There's some odd pieces in some of these such where, say, the grain runs the wrong way.

First, I rebuilt the Sysport Clone (http://www.sawmillcreek.org/showthread.php?77685-Festool-Sysport-Clone) (which got a twin after that thread) to fit on a wall that hasn't been real well utilized for some time. I've been using more Systainers for other tools so my collection has grown further.
275171

Then I built some new cabinets for under my outfeed table. I used to have a couple metal toolboxes here which were pretty inefficient for space utilization. The drawer fronts are just prefinished maple ply. I rounded over the edges and probably should wipe some finish on them. My wife saw this today and said she wants the same in her craft room in the house so I'll probably be doing it all again.
275170

Then I started on a replacement for a hand-me-down metal office cabinet and an old cabinet from my master bath that were in my office.
275169

All to help eliminate a run of hand-me-down cabinets in one corner of my shop to make room to move this over from my dad's shop.
275172

[Michael Dunn]

Nice!!! Everything looks great Matt. Very good ideas. I have similar plans for my festool. I plan to make it fit atop my syscarts. I'd like them to retain their mobility as well as to be able to be put in place in my van for site work. I also want to use drawer slides for each systainer shelf. I hate having to open one systainer with others latched on top or to completely separate my classic systainers.

[Don Morris]

Nice Matt, as always, well done. I really like the storage area under the outfeed table. I'd love to do that, but in my small basement shop, I need the flexibility of being able to move the TS, which would require dropping the outfeed table down (used Jim Becker's design for outfeed table). I have a couple things under it, but you're right, the space under it isn't used as efficiently as it could be.

[Mike Cutler]

Nice work Matt. Very clean lines!
Well done.

PS.
That looks like a nice little lathe there.

[Brian W Smith]

Cool lathe.....they are just so handy to have in a pro-woodshop.

When you get time,I'd enclose the base of it.It'll stiffen it somewhat...but the real benny is "stowage" for specific tooling.If you dig around the web you should easily find some absolutely jawdropping wooden cabinet's,many were factory options.Look at some of the neat collet holders in drawers.You also can store other tooling in these drawer systems(done in wood BTW).

Cpl places to check for inspiration would be Hardinge,Wade,and Moore.

[Alan Lightstone]

Nice, Matt. Very nice.

I'm working on redesigning and rebuilding my outfeed table now, and it was nice to see yours. Are the shims to level it, or another purpose?

I've got my Systainers in two of their rolling carts, and I agree, the system for pulling them out is annoying. Especially on the lower ones. I do like the ability to lock them in, though.

And what is going in the hole above the sandpaper in picture 3?

[Matt Meiser]

Yes shims are for leveling. Or at least get it in the same plane as the out feed. The floor is very out of level there

There's no counter on the cabinets yet. That's just a scrap of plywood because I needed something to hold the UPS and NAS that I use for "offsite" backups. I'm thinking about picking up some butcher block tops from ikea as they aren't much more than doing laminate in the big scheme of things. Also thinking about just using tempered hardboard over plywood--but I'm not sure that's much less.

[Matt Meiser]

Brian, a new stand is in the plans. I have a set of salvage legs (more like piers), some leveling feet and some 8/4 oak that's useless for any fine woodworking and was thinking of putting something together from all that but I'll check around for ideas first.

[Dave Lehnert]

Looks good Matt.
I need to get in my shop and redo some things.

[Sid Matheny]

Looking neat and everything in it's place! Want to come fix my shop next. :rolleyes:


Sid

[Matt Meiser]

Little more progress...

275359

[gary Zimmel]

You can't beat shop furniture....
Nice job Matt.

[Matt Meiser]

Thinking about doing something different with this finish-wise and doing a painted finish. Probably no opportunity to do that in our house, especially with everything being redone in the last several years. We thought about it in the kitchen briefly but decided against it. I recall seeing painted oak cabinets in displays and thought they looked nice.

[Brian Kincaid]

Matt,
I'm about to build some of these in my garage as well. What length of slide did you use? I saw from your other thread you used gliderite(?) where did you order them? I've only used KV but they are way too expensive and nice for this type of project.

Also, did you make them reconfigurable height? If so what spacing did you use for the holes?

-Brian

[Matt Meiser]

Got the cabinets done. This was a potential option for kitchen cabinets we decided against. I didn't really know where I was heading with these, but I decided to give this a try since its "just" shop cabinetry. I used Sherwin Williams's Proclassic which sprayed like a dream with a #5 needle/cap set in my Fuji gun. The primer they recommended, not so much so I need to find a better option there. Ended up having to brush out the primer after spraying. They didn't turn out bad but there are definite brush marks, all in the primer. The tops are from Ikea as discussed in another thread.

275654

I went ahead and replaced the desk top where my shop PC sits too. I plan to replace the metal filing cabinet with something shop built, but probably with less file and more shelf or shallow drawer space. Maybe replace the cheap shelves on the wall too.

275655

[Michael Dunn]

Got the cabinets done. This was a potential option for kitchen cabinets we decided against. I didn't really know where I was heading with these, but I decided to give this a try since its "just" shop cabinetry. I used Sherwin Williams's Proclassic which sprayed like a dream with a #5 needle/cap set in my Fuji gun. The primer they recommended, not so much so I need to find a better option there. Ended up having to brush out the primer after spraying. They didn't turn out bad but there are definite brush marks, all in the primer. The tops are from Ikea as discussed in another thread. <img src="http://www.sawmillcreek.org/attachment.php?attachmentid=275654"/> I went ahead and replaced the desk top where my shop PC sits too. I plan to replace the metal filing cabinet with something shop built, but probably with less file and more shelf or shallow drawer space. Maybe replace the cheap shelves on the wall too. <img src="http://www.sawmillcreek.org/attachment.php?attachmentid=275655"/>

Looks great... I can't believe you painted those cabinets though. I thought they looked beautiful before. Paint job looks nice... In the photo. Did you scuff sand prior to spraying? Was there a clear coat on the cabinets? Or was it bare wood?

[Matt Meiser]

Bare. The pics are a little deceiving as the ply for the panels was pretty cruddy. It would have looked fine either way but I wanted to try something different.

[Alan Bienlein]

My wife just saw the before and after on those shop cabinets you painted and said you ruined them by painting them.

[Matt Meiser]

Decided that the metal brackets and white particle board shelves didn't look right across from the new base cabinets so I built and painted this Friday and Saturday. The only thing I purchased for this is a piece of beadboard plywood for the back. The finish on that is the last little bit of tinted shellac I had left from my kitchen last year and Endurovar--gotta love the 3M PPS system which stored both for a year ready to spray. The main carcase is Arauco ply from Menards that was left from something I did for my parents. Its got one really nice face and one so-so so I had to carefully choose the pieces for the middle and bottom shelves and do a little filling. I didn't have enough that was wide enough so one piece is even glued up like I would hardwood! Most of my oak short/narrow stock and some more of the junky 1/4" ply for the panel on the end. Even the crown is some of the excess from the kitchen.

276128

[George Bokros]

Lookin good Matt. Like the color of the cabinets.

[Malcolm Schweizer]

I also like the color, and normally I am a "leave it natural" kind of guy. Looks good.