Steven Wayne
07-28-2013, 12:34 PM
My shop has high leg delta 3 phase power service. I lucked out and found a very good condition 3 phase panel on cl for $35 and got it wired in to the main disconnect. Then, I set out looking for too goo to pass up deals on 3 phase machines and found this:
(photos from cl ad)
https://lh3.googleusercontent.com/-8atn5wlKDhE/UfVC50yGllI/AAAAAAAAHho/QOdSc9KVth0/s800/IMG_6647.JPG
https://lh5.googleusercontent.com/-6gt66TZqfI4/UfVC6MKTQxI/AAAAAAAAHhw/ym5gIqvCyYw/s800/IMG_6648.JPG
Got it home and took the extension off the left side.
https://lh3.googleusercontent.com/--46IZo0Sk3s/UfVC6-DCFUI/AAAAAAAAHh4/A5cZeLreppU/s800/IMG_6649.jpg
I bought it from a company that bought out a mill. It is in good condition overall. I sent the blade out for sharpening. I rigged it off the pallet and onto the floor.
https://lh3.googleusercontent.com/-gwnB63S11SI/UfVCWaIM9RI/AAAAAAAAHhY/fBqOQmX2zks/s800/IMG_7984.jpg
https://lh3.googleusercontent.com/-zaqLDvRsTDk/UfVHUfNMcvI/AAAAAAAAHiI/UEPvMeCpb48/s800/IMG_7985.jpg
This photo shows the current condition and some other OWWM.
https://lh4.googleusercontent.com/-yerXUmj6Ze8/UfVCxNt6hHI/AAAAAAAAHhg/Frp6p6Q5Psg/s800/IMG_8019.jpg
My copy of the Mr. Sawdust book arrived this week. It was a great read. I'm now at the place where I decide what to do with this big old saw. I put together low voltage controlled magnetic starter and got the original pushbuttons on the end of the arm working. It spins on for over 3 minutes after being switched off. Hoping theres a good brake setup out there.
I have found references to using unistrut to mount the table. This interests me. I have some strut on hand.
Can anyone chime in on the table setup with strut? I'm thinking people are using the strut to mount their Mr. Sawdust style table..
(photos from cl ad)
https://lh3.googleusercontent.com/-8atn5wlKDhE/UfVC50yGllI/AAAAAAAAHho/QOdSc9KVth0/s800/IMG_6647.JPG
https://lh5.googleusercontent.com/-6gt66TZqfI4/UfVC6MKTQxI/AAAAAAAAHhw/ym5gIqvCyYw/s800/IMG_6648.JPG
Got it home and took the extension off the left side.
https://lh3.googleusercontent.com/--46IZo0Sk3s/UfVC6-DCFUI/AAAAAAAAHh4/A5cZeLreppU/s800/IMG_6649.jpg
I bought it from a company that bought out a mill. It is in good condition overall. I sent the blade out for sharpening. I rigged it off the pallet and onto the floor.
https://lh3.googleusercontent.com/-gwnB63S11SI/UfVCWaIM9RI/AAAAAAAAHhY/fBqOQmX2zks/s800/IMG_7984.jpg
https://lh3.googleusercontent.com/-zaqLDvRsTDk/UfVHUfNMcvI/AAAAAAAAHiI/UEPvMeCpb48/s800/IMG_7985.jpg
This photo shows the current condition and some other OWWM.
https://lh4.googleusercontent.com/-yerXUmj6Ze8/UfVCxNt6hHI/AAAAAAAAHhg/Frp6p6Q5Psg/s800/IMG_8019.jpg
My copy of the Mr. Sawdust book arrived this week. It was a great read. I'm now at the place where I decide what to do with this big old saw. I put together low voltage controlled magnetic starter and got the original pushbuttons on the end of the arm working. It spins on for over 3 minutes after being switched off. Hoping theres a good brake setup out there.
I have found references to using unistrut to mount the table. This interests me. I have some strut on hand.
Can anyone chime in on the table setup with strut? I'm thinking people are using the strut to mount their Mr. Sawdust style table..