May I please see your Miter Saw Stations

[John Dingman]

Hey all,

I currently have a detached shop. But, because of a recent move to a new home, and the pending demolition of my current shop building, I have been working on a new basement shop. I am just about ready to start moving my stuff over when I start thinking, maybe my current miter saw bench is too big. Here's a pic of it:

http://www.johnswoodshop.us/Images/shop%20pics%20010.jpg

It's 16' wide. I have the space for it in the new basement shop, but I was wondering if it might be an overkill. Can you guys post pics of what you are using and tell me what you like and don't like about it. I really appreciate your help.

Thanks,
John

[CPeter James]

This is mine. It is a rebuild of a cabinet out of a school chemistry lab. The wings fold down and are long enough to put an 8' board on them and cut off a little from the end ( from blade to end of wing = 4'). It is on casters, the front two lock.

CPeter

[Steve Cox]

My miter saw actually is stored in an outbuilding and only used on jobsites. I have a Jet aftermarket sliding table for their cabinet saw. It gives me the ability to crosscut sheet goods and to not need a miter saw in the shop. Just a thought.;)

[CPeter James]

On my old saw I had an Exactor sliding table and it did work real good, but I process a lot of rough lumber and like to be able to rip and crosscut with out changing the setups.

CPeter

[John Keane]

John, ShopNotes vol 2 Issue 11 has plans for a portable miter saw station. I have built two of them and use the current version all the time. The portability is that you can reverse the wings and fold them inside to pick it up and bring it to a job site. It supports my Hitachi SCMS, and could fill the bill for you. I just happen to have two copies of this shop notes. Send me a PM or e-mail and we can take it from there. Sorry, I don't have a pic

[Alan Mikkelsen]

I have two. One for jobsites and one for the shop. Here's a couple of pictures.

[Corey Hallagan]

I wouldn't say it is overkill unless you never use that much table, but while I have been doing a lot of molding work in my remodelling, I know I could have used that station very efficiently :) I say keep it if you have the room to spare!

Corey

[Corey Hallagan]

Alan, I love your shop set up station. If I had the room to do a shop set up it would be like yours with storage for cut offs etc. under neath. I think Wood magazine just did a shop remodel as well and theres was about the same size and allow for the storage a 6 1/2 inch Jointer.

Corey

[Chris Rosenberger]

This is mine.

[Hunter Wallace]

John, I don't think your miter saw bench is too big,
I think your saw is too small!!!!

[Corey Hallagan]

Wow, nice set up Chris, Kreg Foreman and all!!

Corey

[John Dingman]

Thanks all for the pics and the advice. I am hoping some more folks will jump in.

Chris, that is one awesome miter saw-kreg jig-RAS station you have there. Nice storage too.

Thanks Guys,
John

[Martin Shupe]

John, I don't think your miter saw bench is too big,
I think your saw is too small!!!!

Hey Hunter, can you show us a full sized pic of the clock in your Avatar? It looks nice, but it is so small I can't see the detail. You can show us in this thread (sorry about the hijack) or start a new one. Just show us!

Thanks!

[Chris Rosenberger]

Thanks Corey & John.

[Bob Johnson]

I have just finished mine, its based on the one in Wood Magazine Dec 1999. I added a lift off hood to contain the dust. I used a 12 x 6 x 6 register boot to connect to the dust collector. With the dust collector running it seems to get everything, including the small offcuts. However, if you cut a piece of MDF without turning on the dust collector you get a big cloud of dust blown back out at you.

Bob

[Corey Hallagan]

Bob, another great looking and very mobile miter station. Nice work!

Corey

[Lamar Horton]

Here is my new upgraded Miter Saw Station. Miter Saw is, Porter Cable 10" Twin Laser. The stops are from Woodworker Supply. So far I'm very happy.


http://www.handcraftedbylamarhorton.com/assets/images/Miter_Saw.jpg
http://www.handcraftedbylamarhorton.com/assets/images/Miter_Station.jpg

Don't ask about the carpet on the wall, it was there when we moved in and I have been searching for the elusive round tuit, so I can take it down.

[Kurt Voss]

Here is my new upgraded Miter Saw Station. Miter Saw is, Porter Cable 10" Twin Laser. The stops are from Woodworker Supply. So far I'm very happy.


http://www.handcraftedbylamarhorton.com/assets/images/Miter_Station.jpg

Don't ask about the carpet on the wall, it was there when we moved in and I have been searching for the elusive round tuit, so I can take it down.

If you'll just leave that carpet there for a while, you'll have a "scatter plot" to base dimensions on for a dust collection hood ;) .

[Jeff Sudmeier]

Here is mine.

Basically a miter saw attached to some old kitchen cabinets. Some day I am going to build a fence for it with built in stops.
http://www.woodworkersweb.com/modules/gallery/albums/albut49/100_7825.sized.jpg

[Jim Becker]

You can see a complete contruction pictorial (http://sawsndust.com/a-miterstation.htm)of mine at my site. This is a cantilevered design originating with Chris Gochenour/Fine Woodworking with some modifications to best suit my shop.

(old picture...)

http://sawsndust.com/images/miter/miter.jpg

[John Dingman]

You can see a complete contruction pictorial (http://sawsndust.com/a-miterstation.htm)of mine at my site. This is a cantilevered design originating with Chris Gochenour/Fine Woodworking with some modifications to best suit my shop.

(old picture...)

http://sawsndust.com/images/miter/miter.jpgJim,

That is awesome! Outstanding Idea!

John

[Jim Becker]

John, I chose this design for the practicality...nothing in the way under it so my "heavy" lumber (10/4, 8/4, etc.) has a place to live and additional lumber storage over head. (I have some primo wide 5/4 and 4/4 cherry up there waiting for the right project) My only regret is putting it where I did. Now that the shop is bigger, it would be much better on the back wall where my lathe lives, but 5 years ago when the shop was 17' x 21', this was the only place it could go. And it would be nearly impossible to move at this point.

[Daniel Rabinovitz]

Here is the link to the original photo.
http://www.sawmillcreek.org/showthread.php?t=1058

Daniel