My Dream Router Table

[Dan Schmidt]

Warning - Major Gloat Ahead:


I just finished my new router table. Inspired by Norm, the design has been stretched/pulled/modified to include:

Bench Dog cast iron top
Casters for mobility
4" dust collection
Heavy duty drawer slides on bit trays + drawers
Integrated Wixey digital height gage
Concealed wiring
Some pics:

[Todd Miltier]

First class!!

ps. you missed a wire;)

[Aaron Wingert]

Dan that thing is the cat's pajamas. I'm totally jealous of the cast iron top. Nice work.

[Will Overton]

Very nice Dan. I don't think I've seen that table built with the CI top before. :cool:

[Von Bickley]

Dan,

Super Nice.....

[Doug Carpenter]

We're not worthy, we're not worthy!

That is truly awsome. Norm would turn in his flannel shirt if he saw that one.

[Mike Harvey]

Great Job. You should be proud of that table!!

Mike

[Bruce Page]

Saaaaweet!

[Julian Wong]

Gloat it is!

I see that it's not broken in yet - No sawdust on it. Now put it to use!

[Mike Zilis]

That's gorgeous. I built the same table a few years ago when I first started woodworking. Your's puts mine to shame by a country mile.

Great work.

Mike

[Bryan Hunt]

That's a sweet router table. I'm about to build a similar table and may borrow several parts of your design. :) How did you decide on that design for the dust collection? I was thinking it might be better to have the dust port just under the table so the shavings don't get sucked into the air intake on the router motor.

[G. Brad Schmidt]

Heck, I'm jealous of your craftsmanship AND your collection of Whiteside bits!
Dan, I think your RT outshines Norm's. http://smileys.on-my-web.com/repository/Winks/wink-3.gif


http://www.clicksmilies.com/auswahl/ernaehrung004.gif (http://www.clicksmilies.com/s1106/ernaehrung/food-drink-smilies.html)

[Van Huskey]

REALLY nice!

[George Sanders]

Incredibly well done!

[Rod Sheridan]

Wow!

That's really superb.................regards, Rod.

[glenn bradley]

That's a looker. Very well done.

[David Thompson 27577]

Warning - Major Gloat Ahead:


I just finished my new router table. Inspired by Norm, the design has been stretched/pulled/modified to include:

Bench Dog cast iron top
Casters for mobility
4" dust collection
Heavy duty drawer slides on bit trays + drawers
Integrated Wixey digital height gage
Concealed wiring

Some pics:


Hey Dan -- looks great!

I have a few questions, since I am considering replacing my (left-wing-mounted) router table.

If you have used it enough to know......... do locking casters lock tight enough that the whole table stays in place while you are routing something big? I sometimes do some really wide profiles, requiring double-fingerboards in two directions. That holds the stock tight to the table and fence, but takes a lot of 'push' to get it through.

And -- is there any way that you have integrated the dust collection below the plate, with the collection at the fence? In my experience, dust and chips fly in almost every direction from a router bit.

[Ray McCullie]

What kind of finish did you use on the wood?

It looks great but I hope you finish the wood so it'll be protected after all that work.

[Eduard Nemirovsky]

Now I can't sleep:D, every time I closing my eyes - I see your table:D:D:D
Very nice , thank you for showing.

ed.

[Harold Burrell]

WOW!

That table wouldn'tr work for me, though. Because if I were to build something that nice, my wife would want it in her dining room. :rolleyes:

[Dan Schmidt]

Thanks to all for the comments. Some answers to your questions:

Q: That's a sweet router table. I'm about to build a similar table and may borrow several parts of your design. How did you decide on that design for the dust collection? I was thinking it might be better to have the dust port just under the table so the shavings don't get sucked into the air intake on the router motor.
A: Dust collection was inspired by Norm; I simply modified several of the dimensions and increased port size to 4". You have point there - I'm sure I will have some bits sucked into the motor. No matter what, I expect that chips will settle to the bottom, and my thoughts were to extract from that level to prevent all "build up". Not being 100% sure myself which strategy was best, I went with a tested design - I think thousands of Norm RT's have been made, and most people say they are happy with it.

Q: What kind of finish did you use on the wood?
It looks great but I hope you finish the wood so it'll be protected after all that work.
A: I used General Finishes "Arm-R-Seal" which is an oil/urethane blend. 2 coats on inner surfaces; 4 coats on outer surfaces with 0000 steel wool in between.

Q: If you have used it enough to know......... do locking casters lock tight enough that the whole table stays in place while you are routing something big? I sometimes do some really wide profiles, requiring double-fingerboards in two directions. That holds the stock tight to the table and fence, but takes a lot of 'push' to get it through.
A: I was concerned about this as well. I used the same casters (great quality; Woodcraft) on a different project (roll around tool cart) a few years ago. I tested the rigidity on this cart before starting my RT. It helped to put non-swivel casters on rear (rolls front to back), with swivel on front. When I push sideways on the table, the first thing to "give" is the slippage of the casters along the concrete floor. This takes a "lot" of force - more than I think I will EVER need. The CI top and hefty cabinet adds a LOT of weight, and this helps of course.

Q: And -- is there any way that you have integrated the dust collection below the plate, with the collection at the fence? In my experience, dust and chips fly in almost every direction from a router bit.
A: I haven't connected yet, but my intent is to connect the 4" bottom duct to my DC system, and "y" the 2" fence duct into this. I'm hoping this will be robust, but I'll let you know how this works....

[Dan Henry]

Your router table is beauty!! What is the gadget on the upper right front of the cabinet??

Comment on the dust collection. I put standard shop vac hose fitting behind the fence at the bit opening and ran hose to hole in the area next to the 4 inch hole below the table top and the space has enough negative pull to capture the chips coming off of the bit at the top, do you have make up air holes in the router door, if not you need around (5) 1 inch holes to ensure air will flow through the router area.
With this set up I capture 95% of the router chips when I am using the fence, when free handing curved shapes I loose some.

Dan

[Fred Floyd]

I built the Norm version a few years back. Yours appears similar, but with some well thought out improvements. Most notably the table top.

This should be in the living room... Well done.

[Dan Schmidt]

Thanks. The gadget to the upper right is a remote digital readout which allows very precise and easy indication of the height of the bit. This one is the Wixey model mounted to a block of oak which is secured to the cabinet with rare earth magnets. Let me know if you are interested in additional pictures of this.


http://www.wixey.com/remote/index.html