View Full Version : A bit of She-oak, add some brass and ...
Derek Cohen
02-28-2009, 11:52 AM
I decided to make another brace. This is small, to be used as would an eggbeater, such as for drilling holes for screws. It can also be used as a driver.
The total length is 400mm (15 3/4") with a 100mm (4") throw.
Materials: West Australian She-oak body and Tasmanian Blackwood pad.
http://i13.photobucket.com/albums/a262/Derek50/Drills/AWR%20Brace/Brace-complete3.jpg
http://i13.photobucket.com/albums/a262/Derek50/Drills/AWR%20Brace/Brace-complete2.jpg
The pad ...
http://i13.photobucket.com/albums/a262/Derek50/Drills/AWR%20Brace/Brace-Pad2.jpg
An old, rusty Stanley brace sacrificed itself for the upper connection. This turns so sweetly.
http://i13.photobucket.com/albums/a262/Derek50/Drills/AWR%20Brace/Brace-Pad3.jpg
Finally, the chuck is made from a spring-loaded clip-on driver holder. I wire brushed the anodising back to a steel finish.
http://i13.photobucket.com/albums/a262/Derek50/Drills/AWR%20Brace/brace-chuck1.jpg
Construction: I turned the pad on my lathe. After bandsawing out the basic shape, the final body shape was achieved with rasps and scrapers. The She-oak is so hard and interlocked that my spokeshaves just bounced off! Sandpaper to smooth. Oil and shellac to finish.
Thanks for looking.
Regards from Perth
Derek
Bruce Page
02-28-2009, 11:56 AM
Wow Derek! That is beautiful!
200 years from now somebody will have that in their prized collection.
Dewey Torres
02-28-2009, 11:58 AM
WOW,
Nice work. You might be the first one I have seen to actually build one of these. It is a beauty!
Berl Mendenhall
02-28-2009, 12:13 PM
Derek,
You do such really fine beautiful work. Your tools are great!
Berl
John Keeton
02-28-2009, 1:08 PM
That's really a great looking tool! You comment in many of your reviews and posts about the hardness of the native Aussie woods - what is with that? Seems like most all of your available hardwoods are, well, HARD! Is it the climate, soil - just curious. As I have commented before, although I think they are beautiful, I never work in exotics, so their characteristics are intriguing.
Jim Koepke
02-28-2009, 1:11 PM
Great work and it looks like it works great.
jim
Gary Herrmann
02-28-2009, 1:41 PM
Beautiful job as always, Derek. I really like the curve.
Derek Cohen
02-28-2009, 8:29 PM
That's really a great looking tool! You comment in many of your reviews and posts about the hardness of the native Aussie woods - what is with that? Seems like most all of your available hardwoods are, well, HARD! Is it the climate, soil - just curious. As I have commented before, although I think they are beautiful, I never work in exotics, so their characteristics are intriguing.
Hi John
We have a lot of eucalypts. It is not just that they are hard (and they are very hard - see below) - they also have short, interlinked grain that frequently reverses. This is what makes it so important to plane with a high cutting angle. It really sorts the men from the boys (apologies for a sexist comment).
Here is a link to a list of international timbers. You can look up their hardness/density ratings, etc:
http://www.worldwideflood.com/ark/wood/timber_list.htm
I frequently use Jarrah (hardness rated here at 8.5), Karri (9.0) and She-oak (14). By comparison, look at the ratings for USA Sugar Pine (1.2), Poplar (2.3), White Oak (6.0) and hard Maple (6.9).
Regards from Perth
Derek
Berl Mendenhall
02-28-2009, 9:51 PM
Wow, I thoutht Maple was hard. It's not even close to your stuff. That stuff would be like tring to plane tangled twisted wire. Gives me a whole new appreciation for SYP and Poplar.
Berl
Louis Reed
02-28-2009, 10:20 PM
Keep the posts coming, I enjoy your work and comments.
Louis
John Keeton
03-01-2009, 6:56 AM
I frequently use Jarrah (hardness rated here at 8.5), Karri (9.0) and She-oak (14). By comparison, look at the ratings for USA Sugar Pine (1.2), Poplar (2.3), White Oak (6.0) and hard Maple (6.9).I can envision my router bits exploding on contact!! Oooppss, shouldn't have said that in the Neander forum!
David Keller NC
03-01-2009, 10:09 AM
"I frequently use Jarrah (hardness rated here at 8.5), Karri (9.0) and She-oak (14). By comparison, look at the ratings for USA Sugar Pine (1.2), Poplar (2.3), White Oak (6.0) and hard Maple (6.9)."
Interesting - I'm guessing that she-oak is also very interlocked and nearly impossible to split, hence you can get away with the beautiful form of that brace. Most all of the beech, hard maple, and birch antiques I've either owned or had the privelege of handling have a rather thick web where the handle turns out and then back in, presumably to prevent the brace from splitting in two when pressure is applied to the head.
Derek Cohen
03-01-2009, 10:20 AM
David
You will just have to take my word that this brace body could have been made even thinner and it still would not flex with a half dozen adults standing on the pad and jumping up and down! :)
Regards from Perth
Derek
Bill White
03-01-2009, 12:19 PM
Hey Derek. Have a bit of an idea for you. Why don't you send me the brace. I'll just copy the pattern, try it out for a year or two, then send it right back to you. (Laughing up my sleeve.)
Well done!
Bill
Derek Cohen
03-01-2009, 7:26 PM
Bill
You got a deal :)
Regards from Perth
Derek
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.