Register
Help
Remember Me?
What's New?
Activity Stream
New Posts
New Group Messages
New Articles
New Events
New Blog Entries
Mark Forums Read
Forum
Articles
Blogs
Donate
Sponsors
Friends of the Creek
Advanced Search
Home
Activity Stream
If this is your first visit, be sure to check out the
FAQ
by clicking the link above. You may have to
register
before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Activity Stream
Filter
Sort By
Time
Show
Recent
Recent
Popular
Popular
Anytime
Anytime
Last 24 Hours
Last 24 Hours
Last 7 Days
Last 7 Days
Last 30 Days
Last 30 Days
All
All
Photos
Photos
Forum
Forums
Articles
Articles
Blog
Blogs
Groups
Groups
Filter by:
Groups
Clear All
New Activity (
)
Please reload this page to view the 200+ new activity items that have been created.
Older Activity
06-06-2023,
6:25 PM
Sam Fleisher
replied to a discussion
I am the sorta proud owner of a brand new G0632z Lathe
in group
Grizzly Green Monster Group
Good you can start turning. They have kept that model with a metric tool rest post still? What will you do, switch your internals from your old...
see more
10 replies
06-06-2023,
1:23 AM
Joe Hightower
replied to a discussion
I am the sorta proud owner of a brand new G0632z Lathe
in group
Grizzly Green Monster Group
I am now up and running! Excited to start turning. Interesting new problem to solve. I can rotate the headstock with a bowl I plan to finish...
see more
10 replies
06-02-2023,
2:59 PM
Brian Robison
started a discussion
Old Trotec
in group
Trotec Laser Engravers Users Group
Good afternoon, I got an old Trotec and everything seems to work. Once I get in my new shop I have some questions. FYI, I've had an Epilog since...
see more
1 replies
06-01-2023,
11:31 PM
Sam Fleisher
replied to a discussion
vacuum chuck
in group
Grizzly Green Monster Group
Up and running frugal vacuum system! With a lesson thrown in as well. Remember boys and girls..... when you just can't wait to see how it works...
see more
13 replies
05-27-2023,
6:07 PM
Sam Fleisher
replied to a discussion
vacuum chuck
in group
Grizzly Green Monster Group
I don't suppose anyone is using the frugal set up with an sk114 axminster chuck? I made some vacuum chucks already and I'm worried it's going to be...
see more
13 replies
05-25-2023,
9:48 PM
Sam Fleisher
replied to a discussion
vacuum chuck
in group
Grizzly Green Monster Group
Update! Was told today that the frugal pumps might be going out next week after the holiday so fingers definitely crossed. It's been a wait. I've...
see more
13 replies
05-23-2023,
9:45 AM
Roger Chandler
replied to a discussion
shaft turning on tailstock
in group
Grizzly Green Monster Group
I think David gave you the correct advice. That screw must be extended in the groove, but not bottomed out, almost to the point it touches. Do...
see more
4 replies
05-23-2023,
2:01 AM
Sam Fleisher
replied to a discussion
shaft turning on tailstock
in group
Grizzly Green Monster Group
I can't remember, did we have to assemble that when it was new or did it come assembled? Regardless, you'd think they would have put in a bearing...
see more
4 replies
05-22-2023,
4:28 PM
David C. Roseman
replied to a discussion
shaft turning on tailstock
in group
Grizzly Green Monster Group
Sam, yes, it sounds like that's what's happening, so you've probably solved the issue by now. And if the lock lever pin isn't in the key slot, it can...
see more
4 replies
05-21-2023,
1:06 AM
Sam Fleisher
started a discussion
shaft turning on tailstock
in group
Grizzly Green Monster Group
My tailstock shaft where the numbers are for measuring has started to turn as I tighten the hand wheel so I hold on to it while tightening. Before...
see more
4 replies
05-13-2023,
5:29 PM
Joe Hightower
replied to a discussion
grizzly bowl turning tool rest
in group
Grizzly Green Monster Group
No but I have a few things to turn that will be larger than 16 inches
see more
3 replies
05-13-2023,
10:05 AM
Sam Fleisher
replied to a discussion
grizzly bowl turning tool rest
in group
Grizzly Green Monster Group
Plan on making table tops or something?
see more
3 replies
05-12-2023,
11:47 PM
Joe Hightower
started a discussion
grizzly bowl turning tool rest
in group
Grizzly Green Monster Group
Does anyone have experience with the grizzly t28011 bowl tool test? How deep of a bowl can it be usef with? Any comments or thoughts?
see more
3 replies
05-12-2023,
11:45 PM
Joe Hightower
replied to a discussion
I am the sorta proud owner of a brand new G0632z Lathe
in group
Grizzly Green Monster Group
If anyone is still following ... my electrician will hardwire the lathe with a cutoff switch. Then we can use a non gfci breaker and I can turn! A...
see more
10 replies
05-12-2023,
8:05 AM
David W Arnold
replied to a discussion
Indexing plunger
in group
Grizzly Green Monster Group
I found them at Lowes or HD, can't remember which one. Three for under ten dollars. They measure 3/4" round and 1/8" thick with 3/8" hole. Dave
see more
7 replies
05-12-2023,
7:45 AM
David W Arnold
replied to a discussion
Indexing plunger
in group
Grizzly Green Monster Group
The pin is 10mm. 3/8" is 9.5250 mm. So not very much. I tried to drill the magnet at first. But that didn't end well. Just an FYI, 1/2" is 12.700...
see more
7 replies
05-12-2023,
12:05 AM
Sam Fleisher
replied to a discussion
Indexing plunger
in group
Grizzly Green Monster Group
So you epoxied the magnet to the pin itself? That's probably a better option all the way around. How big did you have to enlarge the hole? ...
see more
7 replies
05-11-2023,
8:15 AM
David W Arnold
replied to a discussion
Indexing plunger
in group
Grizzly Green Monster Group
I epoxied a round magnet with 3/8" hole in the middle. I used a dremel tool with sanding drum to enlarge the hole. Used a thin piece of cardboard...
see more
7 replies
05-10-2023,
10:21 PM
Sam Fleisher
replied to a discussion
Indexing plunger
in group
Grizzly Green Monster Group
I was just wanting it more for the convenience when I'm unscrewing a bowl off the screw chuck and situations like that where I need to use both...
see more
7 replies
More Activity
No More Results
No Recent Activity