I have a Dewalt track saw that needs a new blade. Any experience with Freud/forrest etc as they offer blades now. My current need is cutting cabinet grade plywood.
Thanks
I have a Dewalt track saw that needs a new blade. Any experience with Freud/forrest etc as they offer blades now. My current need is cutting cabinet grade plywood.
Thanks
I recently bought the freud ultimate thin kerf plywood and melamine 160mm blade. I've only used it for a few cuts on my dewalt track saw but it did a great job: no tearout on top or bottom crosscutting 3/4 cherry plywood, and a nice smooth cut.
[eta] since it's 160 mm and not 6.5 inch it very slightly reduces the max cut capacity of the dewalt.
--I had my patience tested. I'm negative--
I bought this 48T Freud about 2 years ago to cut maple plywood for a set of kitchen cabinets. It worked great, it's still on great Dewalt tracksaw doing a great job. I'm a fan of Freud router bits and saw blades, never been disappointed in one of their products.
https://www.amazon.com/Freud-Ultimate-Plywood-Melamine-LU79R006M20/dp/B002IPHG9I/ref=psdc_552292_t1_B002IPGXRO
You can also have your blade sharpened. I keep a couple fresh blades on hand and when two are dull I send them out.
I've wanted to try one of the non-dewalt rip blades for awhile. I think I could live with a 160mm blade if it ripped better than the 48t dewalt.
I have a bunch of the 28t tenryu blades that I use for most applications. Really a good all purpose blade if you straight line lumber and still works reasonably well on cabinet ply. I've buried the blade full depth in 3" thick slabs and it keeps on going
I have used three blades. DeWalt, Freud, and Makita. I have only used them on plywood, and my favorite is the Makita, which cuts really nicely.
The DeWalt is the standard one that came with the saw, it cut fine but not as perfect as I wanted, so I replaced it with the Freud. It was about the same.
The blade that came with my new cordless Makita cuts the best of the bunch for me.
Two track saws, three blades...plywood only. That is the only experience I can report on.
PS: These blades are pretty much interchangeable, but if you interchange, take note of the blade kerf. There are variations, which may or may not affect your rubber strip on the track. Also slightly different diameters.
Rick Potter
DIY journeyman,
FWW wannabe.
AKA Village Idiot.
I also get acceptable performance from Oshlun track saw blades but their main advantage is price. I just noticed Wen offers a 56 tooth 6.5 inch track saw blade. I have a table saw blade from them that was surprisingly useful. But it is almost the same price as the DeWalt - which Amazon has for just over $30. At that price I'd just buy the DeWalt.
No complaints with the Freud thin-kerf.
Erik
Ex-SCM and Felder rep
Got a Dewalt track saw to rip 2"+ walnut slabs and ultimately cut 45* bevels for waterfall ends. Had to make incremental cut depths
due to the load on the saw(hand saw when cuts not thru) New to tracksawing & assumed that was par for the course due to the stock thinkness.
A friend used the saw to cut Sycamore slabs, bought a new Milwaukee blade(40 tooth?) and it ripped thru the 1 3/4" slabs without bogging down.
may be good to consider as well.
I find this curious since I'm pretty sure Milwaukee doesn't make a blade with a 20mm arbor. I guess a 5/8" hole could be enlarged to 20mm for the DeWalt or perhaps a bushing found, but those would seem to be more trouble an expense than it's worth for a commodity blade.
So, it seems likely your friend's xtra performance is morel likely due to a more powerful saw and 8 less teeth that is the milwaukee blade anything special.
Last time I checked , Makita's blades are made by Tenryu - very good blades.
Freud makes 165mm x 20mm blades for dewalt, makita , bosch and mafell saws - but they are hard to find in the U.S.
The reason you get poor results is because a 48t blade is prob. the worst blade you could choose to rip solid wood. 14-16t is ideal, and you might get ok results on some with a 28t. A 48t on a track saw is like using a 100t + blade on 10" tablesaw. you wouldn't dream of ripping with that setup would you ?I've wanted to try one of the non-dewalt rip blades for awhile. I think I could live with a 160mm blade if it ripped better than the 48t dewalt.
Jared - if you have flutter with both blades , then you need to check your saw ! It is either misaligned with the track or the bearings are shot. That freud performs flawlessly on my ts55.I have the 14t Freud blade and a 14t tenryu. The Freud has way to much flutter for my liking. Enough that it ate the splinter strip every time I used it. The tenryu is better but still has more flutter than I consider acceptable.