I recently bought this Unilev 15 edge sander, but it doesnt have the fence.
I thought I can get them from SCM but they kept on telling me the machine is too old even after I told them I will be...
Type: Posts; User: Albert Lee; Keyword(s):
I recently bought this Unilev 15 edge sander, but it doesnt have the fence.
I thought I can get them from SCM but they kept on telling me the machine is too old even after I told them I will be...
Bought mine recently for about $750 USD.. one small problem. it doesnt have the fence!!
Its an older model, an Unilev 15m, but I am guessing its the same part as the newer Unilev 150????
...
Bought this SCM shaper for $900, with feeder! weight is 800kg/1700lbs.
517543
I use Hafele all the time, they are big in New Zealand.
Here are a couple of pics of my L'Invincibile si X panel saw, took delivery last year around July?
the thinnest of all the steel plates on the machine is 12mm! thats like 1/2 inch for you folks...
Its not a lot, a small compressor would do the work. I rarely use it because I use soft timber, if I dont turn on the valve, ie, no pressure I can do 0.1mm without getting planner marks on the stock!
515526
Here is what it looks like inside my L'Invincibile S7, you can see the pneumatics above the roller.
finally bought an ovolo cutter block by Omas.
512692
512693
512694
512695
the most I had was 6
two in the spray booth getting sprayed.
one in the assembly bay (drive way) getting boxed up to send to the client
two in the manufacturing process. tenon, tongue & groove,...
the latest view.
added the following since my last post..
SCM L'Invincibile si X
SCM L'Invincibile S7
SCM TI145EP
Nederman S750
507614
You don’t have to sand or scotch brite it.
I had similar issue with my table top and I used Autosol rust EX and the table top is like new. 506969506970
ok this is what I did today.
I levelled the machine first - this was never done after I moved the machine - I assumed the concrete floor was level but it was out by 2-3mm, back being lower.
...
did a quick check last night, the back of the machine is lower than the front by 2mm over 1000mm. this may have caused the issue. I am going to level the machine today and see if this improves things.
To do this properly you will need the property of the timber you are using and the limit state you will be using, you want the bed to flex a little
Making a loft bed for static load is easier,...
***UPDATE***
I have resolved this issue today!
for a while I thought I had an issue with my OMAS cutter block, even took it to a machinist to check, the machinist commented maybe it is the...
I have installed 400sqft of blonde oak 2 years ago and roughly 250 sqft of purple heart flooring just recently.
Regardless how long you leave the flooring to aclimatise to its environment, it will...
I had a few bandsaws in the past.. partly due to size of the shop and mistake on my behalf selling my bandsaw that I shouldnt be selling...
SCM S440, smaller brother of s600
Wadkin B7
Sicar...
My thought too, I can't visualise or think of a reason why it is cutting tapered, and yes you are correct, its tapered from root out to the tip.
looks like another interesting issue that can to...
Joe I will do this check but what I want to know is, the tenon cutter is cutting tapper. why is that? if the sliding table is out of square, ok, I will cut trapezoid, but I am not cutting trapezoid,...
Thanks Joe, I will be doing that. looks like I will be doing a bit of checking today..
it appears the bottom cutter block is cutting concave, the top block is cutting ok if I move slowly.
The...
Almost, this is the one I have.
https://www.scosarg.com/omas-adjustable-groover-d-30-d-250-z4-v4-b-12-5-22
D is 250.
what am I not doing right? I lost about 1mm when I measured it.
The tenon cutter is Omas K408
Was I too quick in moving the carriage?
here is the video link
...
I have been buying new machines from SCM, started with TI145EP, then L'Invincibile S7... and my new panel saw L'Invincibile SI X is arriving April, where I am (New Zealand) I have no issues with SCM,...
I have a SCM Ti145EP. the machine is designed so you can remove the fence for profile and install the fence for tennoning. its 90 deg rotate.
To have it rotated 180 deg, you will be working from...
that is exactly right Greg.
bought it for like $100 USD. it runs, thats about it.