Register
Help
Remember Me?
What's New?
Forum
New Posts
FAQ
Calendar
Community
Groups
Albums
Member List
Forum Actions
Mark Forums Read
Quick Links
Today's Posts
View Site Leaders
Articles
Blogs
Donate
Sponsors
Friends of the Creek
Advanced Search
Member List
Harold Patterson
If this is your first visit, be sure to check out the
FAQ
by clicking the link above. You may have to
register
before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Harold Patterson
Contributor
Find latest posts
Find latest started threads
View Articles
View Blog Entries
Mini Statistics
Join Date
12-22-2010
Last Activity
05-13-2024
6:25 PM
More
2
Friends
Jamie Buxton
Samuel Green
Recent Visitors
The last 8 visitor(s) to this page were:
Brian Deakin
,
ian maybury
,
James Pickering
,
Jim Matthews
,
MARTA TORRES-QUINONES
,
richard patrissi
,
Samuel Green
,
Stewie Simpson
This page has had
6,346
visits
Tab Content
Harold Patterson's Activity
About Me
Friends
Tab Content
All
Harold Patterson
Friends
Photos
New Activity (
)
Please reload this page to view the 200+ new activity items that have been created.
Older Activity
Yesterday,
7:20 PM
Jamie Buxton
replied to a thread
Shop Furniture Polycoat
in
WorkShops
Patty, you say you're from southwest us. If that means southern California, or anyplace in the region that gets mineral spirits approved by the...
see more
11 replies | 422 view(s)
05-06-2024,
6:45 PM
Jamie Buxton
replied to a thread
Bottom Mount 30" Drawer slides
in
General Woodworking and Power Tools
If Thomas is correct, each shelf is going to take a lot of height - his dumb shelf, the height required by the undermount slide, and the rollout...
see more
5 replies | 539 view(s)
05-06-2024,
10:23 AM
Jamie Buxton
replied to a thread
Bottom Mount 30" Drawer slides
in
General Woodworking and Power Tools
To bottom-mount Blum sidemount slides, you can drill your own holes down through the cabinet member. I did that before Blum started putting those...
see more
5 replies | 539 view(s)
05-05-2024,
10:07 AM
Jamie Buxton
replied to a thread
Systainers?
in
General Woodworking and Power Tools
Systainers might be useful to folks who work out of their trucks. But I'm with you: packaging, even high-quality packaging, is kinda useless in a...
see more
25 replies | 2076 view(s)
04-29-2024,
10:26 PM
Jamie Buxton
replied to a thread
Sideboard/End Tables - Design Feedback + Bottom Panel Needed?
in
Design Forum
On the smaller table, there isn't a visible rail for the middle of the top to glue to. I generally attach the top with glue at the middle of the...
see more
15 replies | 2040 view(s)
04-29-2024,
3:18 PM
Jamie Buxton
replied to a thread
Titebond 3
in
General Woodworking and Power Tools
When TB3 came out I jumped on it. A waterproof single component glue! Pretty quickly I had two glue failures. I was went back to 2-part glues.
see more
13 replies | 1475 view(s)
04-25-2024,
3:51 PM
Jamie Buxton
replied to a thread
Outdoor dining table top joinery ideas
in
Design Forum
Your cross grain glue joints are only a few inches long. They should fine. Glue the with water-tesistant glue. I’d use epoxy, but many folks use...
see more
5 replies | 833 view(s)
04-25-2024,
11:36 AM
Jamie Buxton
replied to a thread
Pithy breadboard
in
General Woodworking and Power Tools
A real-world dining table is going to get food spilled on it. You'll want to wipe it up. If the table has cracks and knots and holes in it,...
see more
7 replies | 821 view(s)
04-21-2024,
5:13 PM
Jamie Buxton
replied to a thread
Building another 4 x 4 outdoor dining table
in
General Woodworking and Power Tools
Thermally-modified wood.
see more
23 replies | 1993 view(s)
04-19-2024,
11:01 AM
Jamie Buxton
replied to a thread
Finishing Santos Mahogany
in
Project Finishing
I've finished Santos with solvent based varnish. It works fine.
see more
4 replies | 1001 view(s)
04-18-2024,
4:09 PM
Jamie Buxton
replied to a thread
Shop sawn veneer for chess board
in
General Woodworking and Power Tools
On veneer, I believe that the important thing is to get the veneer glued tightly to the substrate. I’m concerned that if I edgeglue the veneer, the...
see more
3 replies | 466 view(s)
More Activity
No More Results
No Recent Activity
About Harold Patterson
Basic Information
About Harold Patterson
Biography:
Of Jamaican descent, interested in period furniture, mainly 18th century. Married with two grown children.
Location:
Newtown, ct
Interests:
Photography, Fly Fishing
Occupation:
Retired
Statistics
Total Posts
Total Posts
53
Posts Per Day
0.01
General Information
Last Activity
05-13-2024
6:25 PM
Join Date
12-22-2010
2
Friends
Jamie Buxton
Contributor
Samuel Green
Member
Showing Friends 1 to 2 of 2