Chris Hachet
Member

Prototype of the fancy bottom Ash Filler strip...had a problem.. Can NOT have this gap....so..remake a new, Improved one..and zero gap... ...

And, somehow get the Case up onto the tablesaw's top.. A bead of glue along one edge...screws to attach the plywood to THAT side....rotate the...

Ok..first off..corner braces..that are used to attach the top to the case.. Just diagonal strips of pine..glued and screwed in each corner...there...

Because...I needed to get this mess off the assembly table, and place Side #2 up there... This time...glue into the sockets...run a bead down each...

Started with just a dry fit.. As this frame was labeled as Bottom frame... Got out the screws, the bottle of glue, a BIG square..and something...

Side #2 is done.. Drawer runners are done.. Back rails are milled... And all are assembled with the front rails..to make 9 frames... ...

Eric Brown ( on this site) would be the one to talk to about this saw... I do have the Bishop No.10 version... That I leave set up for...

Been one of THEM days, today....go to type a reply on a website....circuit breaker the Computer is on ( and the House AC Unit) decided to pop......

So..was a long day...but.. All 9 are done for THIS side...next? Need to transfer all the layout marks to the case's other side...and mill...

Set the rip fence to guide the router.. Have to allow for the router's base...including how far in to go..not too bad...? Got set up to do #8...

Tablesaw as a work table/ Works in MY shop...as long as I remember to lower the blade all the way down.. Set up a router, today.. Block is...

Ok..yesterday...Had to go and bring the Boss home...(LONG story) THEN go out and pay the monthly bills, and Grocery shop....Then a trip across the...

Ok..got all 18 runners done.. However, came time to cut the pine back rails.. There was only enough GOOD 1x 2 left for 1 back rail....Trip to...

Set the router table aside, for now...cut 18 drawer runners on the tablesaw for length.. Here is about half of them....each need a tenon on each...

Ok, dovetail bit was done..time to change bits.. There was a time, long ago, where a router by B&D was all metal, and was a clone of a DeWalt No....

1st Router table use...needed a jig to slide along the fence.. To run parts past a dovetail bit.. 9 "rails", dovetail "Tails" on each...

Will do an "Up-Date" later this evening..once we get the Boss back home and settled in... Warning: Router Table will be in use Warning: Tablesaw...

Thinking the term does or does not include slicks? And maybe not from the realm of Timber Framers? Shorty is 11" long..and a mere 1-1/2"...

ok, to get the rebates milled.. Had to move these out of the way...cauls were a might too close to my arms as they were going by.. Used the...

Curved areas near the feet, used a drum sander in a cordless drill...high rail was lower,,,with a beltsander, and couple spokeshaves..and a palm...

Up date time...the 2 sides were clamped together, inside to inside...the back stiles already have their rebates milled to house the 1/4" plywood...

Had to replace a curvy one.. Had enough "Leftovers" for that.. The wide one on the bottom..isn't quite that wide, any more The best 9 rails...

These 2 planks.. Needed to be cross cut in 24" (Roughly) lengths Then run through the rip fence at 1-3/8" width... Then needed to skinny...

Side #2 is out of the clamps.. And Standing in front of Side #1...back to back...one foot will need trimmed a bit, otherwise, they match up quite...

2 hours and 20 minutes in the shop, today...Results? Well..there is the inside of Side #2...being glued up.. Had to get 8 raised panels and 9...

Shopping trip..$108.86 Need to load this up.. Into this space.. Needed to fold the other back seat down..so the 8' long 1 x 4s will...

Well..I did try to get $20 off....but..he only allowed the 10% the Mall gives...on anything over $40... Cheer Up....Yard Sale Season has started...

The Boss is coming home next Wednesday Afternoon-ish...Same day as Pay Day...I get to go out, and pay the bills that morning, then go pick her up. ...

A dry fit that also involved a panel... Did not go well...seems I will be doing this, tomorrow...again.. The Dreaded Too Fat Rebate....back has...

2 stiles also got their feet sawn... Was a good thing that this was the "inside" for both Stiles.. As both had a few "bad" spots, all on one...